Jump to content
SAU Community

Recommended Posts

Hey Brett, 

For lights in the garage, head to bunnings, they have cheap dual tube 2ft and 4ft fluros, then swapthe tubes over for "daylight" coloured tubes. 

Grab an extension cord per fluro, cut the female end off, and wire it into the fluro, couple of screws each and full daylight everywhere in the garage. I find it great for getting rid of shadows around work benches etc. 

In my old garage I had a 4ft single tube smack over the workbench, and another over the engine bay. Was magical! 

It’s something I’ll look into when the big garage is built out the back, at the moment I’m using the house one and eventually it’s just going to store our everyday cars 

  • Like 1
3 minutes ago, r32-25t said:

It’s something I’ll look into when the big garage is built out the back, at the moment I’m using the house one and eventually it’s just going to store our everyday cars 

Fill the big garage with lights. One can never have enough light in a garage ha ha

  • Like 1
2 minutes ago, Piggaz said:

Shush. Don’t give him ideas. It becomes my job ?.

Brett, every single light should be on a independently switched circuit too, and maybe some coloured LEDs, and power points every 30cm... :P

Ha ha ha

let him wire his own lights in Piggaz... Or should we be concerned it'd be just another flood light tek screwed to the roof? :P

 

1 hour ago, Piggaz said:

Shush. Don’t give him ideas. It becomes my job ?.

Don’t worry your job list is a mile long ?

1 hour ago, MBS206 said:

Brett, every single light should be on a independently switched circuit too, and maybe some coloured LEDs, and power points every 30cm... :P

Ha ha ha

let him wire his own lights in Piggaz... Or should we be concerned it'd be just another flood light tek screwed to the roof? :P

f**k that I’m not wiring shit, want nothing to do with anything that I can’t see and can kill me 

27 minutes ago, r32-25t said:

 

Don’t worry your job list is a mile long ?

f**k that I’m not wiring shit, want nothing to do with anything that I can’t see and can kill me 

So you don't want to come play with even some basic magic parts like this? 

1559365781720290630605.thumb.jpg.94f307af332a6ac34ca4d5d3474c0ab7.jpg

On 01/06/2019 at 1:39 PM, MBS206 said:

Brett, every single light should be on a independently switched circuit too, and maybe some coloured LEDs, and power points every 30cm... :P

Ha ha ha

let him wire his own lights in Piggaz... Or should we be concerned it'd be just another flood light tek screwed to the roof? :P

Glow worms in a jar with an automatic feeder? DONE!

  • Haha 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...