Jump to content
SAU Community

Recommended Posts

But see, when you buy a 34GTR it becomes a part of you.
On your instagram page, you need to state that you have a 34GTR, because the images don't always get the message across. To some people, $75k is a small price for a personality and attention.

  • Like 2

Saved a few of those 40-50k R33 GTRs on carsales to see if they move.. they're still there 

Anyone actually know of anyone that's BUYING them for these prices? :P 

Edited by UNR33L
Saved a few of those 40-50k R33 GTRs on carsales to see if they move.. they're still there 
Anyone actually know of anyone that's BUYING them for these prices? [emoji14] 

I did... I paid almost 60k for mine. In fact it was a little more by the time shipping and roadworthy were included.
I don't regret it as I couldn't land a decent LM Limited for the same price from Japan.

You see that R32 tuner car on speed hunters last week? $130kUSD and it's got China cast-looking wheels and a 90's Japanese turbo.
As much as I love the japs, there are good tuning shops, then there are overpriced and dated tuners.

13 hours ago, Rekin said:

R32 GTR's were going for $18k

Skyline life was good back then.

Just shelled out $600 for a new gtr front bar & it's missing the $400 lip.

Dat gtr tax

If I recall, Alvin picked up his 32R for 12-13k when they were at their lowest

  • Like 1
4 hours ago, UNR33L said:

Saved a few of those 40-50k R33 GTRs on carsales to see if they move.. they're still there 

Anyone actually know of anyone that's BUYING them for these prices?  

 

All relative methinks...it used to be that high 20s were the permanent carsales residents...then it was low 30s...

Even if it's only the cheaper ones moving, the cheapest are now no longer <30k listed

Hard to tell where the investment in one would top out. USA market availability did small wonders for R32s, but will the hype/buzz wait for 33s and 34s? As the cars become rarer, parts more expensive / harder to find, could be an eventual decline in interest

35 minutes ago, UNR33L said:

Toby, if my last employer isn't returning my calls for a group certificate request can I just use my last pay slip? Has gross YTD and tax YTD on it should be fine? 

Has it pre-filled? They should have reported by now

Thought it was a relatively large / reputable place where you used to work

23 minutes ago, HEKT1K said:

Has it pre-filled? They should have reported by now

Thought it was a relatively large / reputable place where you used to work

Not sure, I usually have a tax guy that does it.

Nah was only 3 people where I was, was made redundant once the work ran out. 

Legally need to give it to employees by 14 July

They dont need to lodge it with the ATO till 31 Oct so may not be on prefill.

 

Yes you can use YTD payslip unless your Payroll officer does something wrong

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...