Jump to content
SAU Community

Recommended Posts

  • 4 weeks later...

Consumer (NZ) just tested HD dash cams. Prices ranged from $109 to $695 but none was considered good quality. It was not possible to read a number plate at more than 5 metres and less than that only if relative speeds of the cars were much the same.

Best of these was DOD LS460W ($250 - $300)

PS there are apparently some apps for your smart phone that wills do the job assuming you can get a suitable forward facing holder.

Link to comment
https://www.sau.com.au/forums/topic/461330-dash-cams/#findComment-7658752
Share on other sites

Brother has the Navman one for $130, does a decent job. I bought the model up for about $170 because the cheaper one wasn't available -Its got a few nicer features but nothing worth writing home about.

Haven't had any problems with either of them

Link to comment
https://www.sau.com.au/forums/topic/461330-dash-cams/#findComment-7659048
Share on other sites

I recently bought the kaiser baas r10+ on sale at super shit auto ATM for $98. 1080p records fairly decent picture quality. Considering all these cams are made in China or best case Korea, its hard to know what your getting. I think its a good idea to buy from a shop that u can return to, just in case. My 2c.

Link to comment
https://www.sau.com.au/forums/topic/461330-dash-cams/#findComment-7659107
Share on other sites

I have a cheap ebay dash cam. Cost $40, and another $25 for a 32gb card. Does the job, records in 720, and will probably do if anything bad ever happens. Just be sure to hard wire it in to keep the ciggy lighter socket for anything else.

Small update, the eBay cheapie appears to have died from this awful Adelaide heat...

Link to comment
https://www.sau.com.au/forums/topic/461330-dash-cams/#findComment-7659939
Share on other sites

Consumer (NZ) just tested HD dash cams. Prices ranged from $109 to $695 but none was considered good quality. It was not possible to read a number plate at more than 5 metres and less than that only if relative speeds of the cars were much the same.

Best of these was DOD LS460W ($250 - $300)

PS there are apparently some apps for your smart phone that wills do the job assuming you can get a suitable forward facing holder.

I had a close call yesterday where a motorcyclist cut in front of me without indicating and then had to emergency brake due to other cars ahead. I knew I couldn't stop in time so I swerved around the bike and missed it by only centimetres. It was oh so close. Bike rider deserved to be hit but that's another story.

When i got home and reviewed the footage on my PC I was able to make out the no. plates on the bike and of all the vehicles in my line of sight from the footage prior to and up to the point of the incident by pausing the footage frame by frame.

So although it is true that you can't clearly make out plates from more than 5 metres, there is a place for these cams and they can be very useful. On this occasion if I had hit the bike rider, the footage was clear enough to be used as evidence and would have clearly shown exactly what had happened and that I was cruising along minding my own business when some f#*kwit decided to just jump in front of me and get cleaned up.

Link to comment
https://www.sau.com.au/forums/topic/461330-dash-cams/#findComment-7659947
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hooley Dooley these things have some history! If i sell them they will need a certificate of providence to prove they have been in the hands of verified RB20 royalty! They have been stored in a plastic tub, away from sunlight and moisture. They are in mint condition. And they will stay that way, as i have sprung the money for a set of shockworks coilovers. I'm just working on getting them in at the moment, after rebushing the rear of the car, and while the subframe was out i welded in the GKtech reinforcement bracing as well.  They will get a workout at Ararat King of The Hill in November. I ran 48s on the short course there a few months ago, and i am hoping with new bushes and shocks in the rear i can launch a bit harder. There was a fair bit of axle tramp when i tried too hard off the line. a few of the corners had dips mid way which also made the car feel a bit unsettled, hopefully this will help there too.   
    • Food for thought, the stock oil filter thread is a 3/4-16 UNF, which has an ID of about 10 to 12mm (according to ChatGPT lol). Now compare than to an 10AN, which has an ID of about 14mm (Raceworks is 14.2mm, Speed flow is 14.27mm).  
    • Yep, totally get that. However hooking in for Generator back up is only a few hundred bucks for the wiring. You could put a couple of those in (for different circuits explicitly) and run a couple of baby generators. Bonus, you can balance them across different circuits, and now have backups in your backup. I'm looking at buying places that won't even have water etc, and I don't mind the idea of getting off the electric grid either, even with everything you've said. This country already has enough power outages that even the mains grid isn't that reliable anymore. I do agree though on spending a bit more to get better gear, and to add some extra redundancy in to the system too.
    • You can set hard reserves on your battery system, and it can't be discharged past that.  
    • That sounds like an excellent idea. But total self-sufficiency means exactly that. You have no-one else to blame when your system faults out and you have no power for a week or two while it gets fixed. You'd have to go the whole hog and get a diesel genny and all the switchover gear, to get you through such times. And, despite the fact that over 20 years, my system has been pretty reliable**, I have seen so many inverter explosions (or less dramatic deaths), panel and roof JB fires, and so on, over that time, to know that the stuff is the same as any other bulk Chinese manufactured stuff. The failure rate is well above zero - both on the equipment and on behalf of the meth addled installation labour force. And then..... warranty and means of redress against the supplier you bought the gear from. Best I can tell is that only a handful of solar companies are still around within 5 years of starting their advertising pitch. They disappear and phoenix like crazy. So, as per 1st paragraph, I suspect the only way to is go balls deep and spend maybe 2-3 times as much as you might think, so that you have every base covered. Plus, know and understand your gear intimately, so you can diagnose problems, sort them out yourself, etc, etc. Plus, probably have to consider upgrading various parts as the years pass, to maintain compatibility with newer stuff, performance and reliability, etc, etc. Whereas, remaining attached to the grid has an ongoing cost that keeps going up even if you use bugger all power from it. But it does provide the fallback in case of the worst case with your own gear. You either pay up front or as you go, I suspect.
×
×
  • Create New...