Jump to content
SAU Community

Recommended Posts

I think you don't understand what I am trying to say, I suggest you do some googling.

I dont need to google anything. I am the one here that made record numbers on -5 turbos. I specifically asked YOU what is the restriction? What is the back pressure ratio on -5's? What is the back pressure ratio change when externally gated? What specifically is the advantage to externally gating these turbos on this engine?

Your motor will breathe, externally gate anything before the collector and you'll make more power.

It's not rocket science.

And congrats on your epic record achievements because it's a US dyno. I'm sure my corolla would make as much power as your setup too if it were on some inflated US dyno :)

Also, calm your farm.

  • Like 3

I dont need to google anything. I am the one here that made record numbers on -5 turbos. I specifically asked YOU what is the restriction? What is the back pressure ratio on -5's? What is the back pressure ratio change when externally gated? What specifically is the advantage to externally gating these turbos on this engine?

congrats you managed to make 800 field mice power with -5s on an American dyno

Your motor will breathe, externally gate anything before the collector and you'll make more power.

It's not rocket science.

And congrats on your epic record achievements because it's a US dyno. I'm sure my corolla would make as much power as your setup too if it were on some inflated US dyno :)

Also, calm your farm.

That is assuming that anything after the collector is in fact a restriction... You have no data showing that it is or that an externally gated setup will benefit this specific application.

congrats you managed to make 800 field mice power with -5s on an American dyno

I would also like to point out that everyone seams to be laying the burden of proof on me. Has anyone here specifically dyno'd on a dynojet to say that it reads high?

And still hasnt seen the strip....

Car will see the strip. Just got the clutch sorted out. Now working on a tire rub issue.

If you love playing statistics wars, I heard the stock market is a fabulous place for that :)

What do statistics have to do with definitive measured data?

FYI - you still have not answered my question.

hint: its because you dont have the information to answer said question.

  • Like 1

It is well known that dynojet number's are ALOT higher than dyno dynamics or mainline dynos here in Oz.

Run it up on a mustang dyno that will give us a far closer number.

Im sorry but on a stock head and stock cooler etc that your car has that power simply isn't possible!

Dynojets are around 15% higher than our dynos on average.

What do statistics have to do with definitive measured data?

FYI - you still have not answered my question.

hint: its because you dont have the information to answer said question.

Don't need any data, proof is in the pudding.. piggaz's turbos were over worked, glowed probably redder than the sun, boost bled down up top.

I don't need to work for NASA to tell you that the housings are too small.

Anyhow, a couple of Nissan SR20s would pull a premium one week before race wars

Look, I was letting this thread sit till we ran the car at the track except I keep getting multiple emails a day with you jack holes cluttering up the tread. I am not stating anything until I run at the track.

So we are looking for high 130mph?

  • Like 1

Look, I was letting this thread sit till we ran the car at the track except I keep getting multiple emails a day with you jack holes cluttering up the tread. I am not stating anything until I run at the track.

So we are looking for high 130mph?

no, need at least 140mph.. Maatouks can do it with less powererererer.

Don't need any data, proof is in the pudding.. piggaz's turbos were over worked, glowed probably redder than the sun, boost bled down up top.

I don't need to work for NASA to tell you that the housings are too small.

Anyhow, a couple of Nissan SR20s would pull a premium one week before race wars

Ok, so the turbos glowed and the boost dropped off...

Turbos glowing - excessive egt.... why?

Boost falls off - Compressor cant keep up (out of flow). Not related to exhaust housing restriction. If anything boost would remain at targeted level because the gases cant escape the engine quickly enough.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
    • With ordering the belt, you're doing water pump and the idler and tensioner at the same time too yes?
    • This is just a dumb way of keeping the wastegate closed to make more boost. Undo it and either follow the factory setup or redo it properly. Manual boost controllers just use a spring preload to determine when to close in response to boost pressure so it no longer vents to atmosphere.
    • So for the wide band is a Bosch 4.9 correct for the Link G4+ along with a Can bus? Just get the Link gear or is generic ok too? Eg here: LINK LINK DIGITAL WIDEBAND CAN MODULE WITH BOSCH 4.9 SENSOR : KYP Performance House  
×
×
  • Create New...