Jump to content
SAU Community

Recommended Posts

31 minutes ago, Robzilla32 said:

So much progress!
Are you unemployed but wealthy?
Stay at home dad with wealthy Mrs?
Teetotal?

Hahah if only, that would be the dream. Nah I'm a sparky, shifts jump around all the time. I was on nights last week then days mon tues and now back on nights for the next couple weeks so will be good time to get a few more things done on her while waiting for the head.

Got a little bit more done on her today. Hardlines almost finished, just have to drill out a couple holes and put the nutserts in. Come up pretty good so far. Also picked up a few fittings and sorted the surge tank block. Bulkheads are installed just need to get the hose down to the hardline and plumb it all up. Decided to go hardline in the boot now as I've got a heap left over from undercar. Hopefully get it a bit sexier in the boot.

qaSJqKd.jpg

BXfhM9s.jpg

gVJYh9P.jpg

IdoSxFo.jpg

LQzPVvM.jpg

OiCmy7O.jpg

Bm9lSU7.jpg

35OOR3D.jpg

 

  • Like 3

Small update, picked up covers that i got dechromed and painted body colour. What an expensive process... looks top shit though! New 26 head is due back tomorrow so next week can put it on and check piston to valve clearances and stuff. Couple gaskets to get as well for exhaust mani too. Car SHOULD be up and running next month. 

Gotta pull the baffles out and give them a clean up, does anyone know where to get new foam inserts?

uQqOGRn.jpg

Cheers matr, end up getting some foam from highoctane.

Exciting stuff happening now! Picked up the head on thursday and starting checking/assembling it all. 

Head is RB26, ferrea 0.5mm stainless valves, bronze valve guides, full 'raceport', and running the custom kelford 272 10.25 cams from the 25 head.

aK4GOi6.jpg

NAAlewW.jpg

Put some playdough in to check piston to valve clearances with the 1.2 gasket and dropped the head on.

wPXKDp8.jpg

Cuorev9.jpg

Put cams and timing gear on to check tdc and set the cam centerlines.

gFojWa9.jpg

Then wanted to strap on the fun stuff for a pic! Cant wait to finish it off.

VbC8SEh.jpg

  • Like 7

How much piston to valve clearence do you have?

I just done this but used the checking spring method, got some light duty springs from bunnings and switched these in cyl 1 and 6 on an inlet and exhaust valve.

Was able to check clearence from 20 degrees btdc to 20 degrees atdc every 2 degrees to see exactly how much clearence there was. With the light springs installed it was as easy as gently pressing down on the lifter until it made contact.

1 hour ago, NEO25T said:

How much piston to valve clearence do you have?

I just done this but used the checking spring method, got some light duty springs from bunnings and switched these in cyl 1 and 6 on an inlet and exhaust valve.

Was able to check clearence from 20 degrees btdc to 20 degrees atdc every 2 degrees to see exactly how much clearence there was. With the light springs installed it was as easy as gently pressing down on the lifter until it made contact.

Haven't measure yet, was more to check if the 1.2 gasket was going to work ok. 

Still need to pull it down and decide if I wanna get CA625 headstuds or not and install new timing kit and waterpump.

Pulled the motor apart for final clean and assembly. Cleaned block, sprayed some hylomar on the headgasket and let it sit for a bit while we cleaned the head down. Popped headgasket on, installed headstuds and dropped the head on and torqued it up then pulled all the buckets up to check the shims hadn't popped out or anything. 

ukimmrB.jpg

Have ordered a few bits and pieces from kudos, needed new waterpump, timing belt, idler and tensioner, RB26 backing plate with fitting kit, rear belt guide, cam cover bolt rubbers, cometic intake and exhaust gaskets and probably a couple other things as well. So motor should almost be ready to go soon ?

  • Like 4

Overnight parts from JAPAN arrived today (not really, just Kudos). Bolted the water pump on after a slight hack job to get it to fit because of the oil gallery bung at the front of the block. Fitted up new idler, tensioner and gates timing belt as well as a new cam cover back plate, old one was a hacked up 25 one... New OEM Nissan parts make me happy ?

Tomorrow if I have time I'll finish off the front and put the covers and balancer on. Might even get to drop it in next week before I go away :O

PRgxSfZ.jpg

  • Like 2

Didn't really do much on her this arvo, not much left to do really. Cleaned the second cam cover out and installed the foam and baffle ready to get installed. Got bored and put it together but covers have to come back off cause mate wants to check centerlines with the new timing belt installed. 

So excited to finally get it in the car after the LONG wait... Motor is silky smooth turning it by hand, should purr like a kitten ?

li1S5jU.jpg

wZSuGNj.jpg

 

  • Like 2
  • 3 weeks later...

No progress atm. Have been away the past week soaking up the sun on Fraser Island. Will be back at it this week. Have ordered a 140A LS alternator kit from @rat32r which will arrive this week! 

Hoping to get the motor in soon, couple things to install on it before we drop it in though. 

Stay tuned!

  • Like 2

So she got towed down to the shop this arvo. First time I've seen the car on the welds not in the garage. Look absolutely sexual, super happy with them! 

VU9ERkY.jpg

XH43rcV.jpg

Got it down the shop and had to take a quick snap with the motor. Super excited to get it in the car running. Should be more progress this week :)

  • Like 7

So we dropped the motor in today to see how it would sit in the car with turbo etc. Motor sits in a sweet position but manifold sits the turbo a bit high and bonnet wont shut :( So gonna have to put some r32 gtr engine mounts in to drop it down 20mm and i hope to go it will shut... Also have a bit of cutting to do on the passenger guard to make the turbo fit how we want it. 

The wastegate is also in a pretty shitty spot, very tight but hopefully once the compressor cover is clocked how we want it it will all work out. 

Might throw the box in and start fabbing up exhaust and things once I sort the engine mounts out. Gotta wait for new SDE converter to be made early next month as well.

For the cold side we have decided to go all out and get a hypertune v2 twin rail plenum and 90mm TB and also hypertune 600x325x100 cooler. Will be running 12x1000cc injectors as opposed to 6x2000s as we will be able to control them better for 98 tuning hopefully. 

This should all happen within the next month or so, so stay tuned! 

Same same but different

QF7oRUD.jpg

UgR81Vf.jpg

KS1fRTk.jpg

nuzzFeX.jpg

  • Like 4

Bit of progress on GOT SUM today :) Managed to find some Nismo GTR engine mounts cheap so picked them up and put them in. Little bit of modding the brackets to get them to sit flush on the mount but nothing too crazy. 5 mins with the grinder and got it sitting nicely. Cleaned the bonnet by about 5mm, hopefully it doesn't lift too much being the torque side. Might have to put an engine damper on or something if we have issues there. The sump sits pretty low now as well which is a bit of a worry with a fair bit still to go onto it. Might have to get some coilovers to put in there and lift it up a bit so I don't bash it on shit.

Mounted the gearbox temporarily as well so we can start fabbing up the exhaust. Just have to order a new vband flange and we can start. It's going to be fun routing the front gate in there as it's very tight next to the compressor cover but we should be able to get it to work. 

1hg6KSW.jpg

SmNqUvV.jpg

06dc68R.jpg

l1UHSyM.jpg

DsLsFHV.jpg

WfXZLWj.jpg

Also almost finished off the hardlines. They're all mounted to the body underneath just need to fix it in the bay and we should be good to go. That will get done this week as well as the surge tank plumbing. It's all slowly coming together, should look pretty cool once it's all done :)

48JZuvT.jpg

YEC2cG4.jpg

  • Like 3

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Welcome to my 2004 Toyota Mark ii IR-V Fortuna (series 2) With a 1JZ-GTE powerplant under the bonnet (hood) it'll give me plenty of scope for power upgrades. For those who aren't familiar with imports, the 1JZ-GTE is a 2.5L 6 cylinder VVTi engine with a single turbocharger. This has the factory R154 5 speed gearbox, along with a aftermarket 2 way LSD differential (brand unknown). Under the arches are a set of CST Zero 1 alloys, 18x9 +30 225/40 up front and 18x9.5 +15 265/35 on the rear. The car was quite low in Japan and there's evidence of the wheels catching the rolled arches/fenders. The tyre's aren't great so I'm in two minds whether to replace both or just the tyres and put up with the wider wheels on the rear. The car still uses stock brakes with the addition of some braided hoses. The exterior is stock with the exception of a BN Sports front bumper and a replacement Fortuna grill  Moving to the interior, the steering wheel has been replaced with a dished MOMO steering wheel (which will get swapped for my Momo Tuner for the time being) Defi Link Gauges are mounted above the climate controls and on the A pillar, the Oil Temp,Oil Pressure,Water Temp and Boost gauges should help with spirited and track driving  The stock seats have been replaced with some retrimmed Recaro bucket seats. Being a larger build these are a little snug, unfortunately the orange isn't for me so I'll look into replacing these down the line. Other modifications include a twin plate clutch, Blitz intercooler, Evolve alloy radiator, a stainless exhaust with decat, HKS EVC-S boost controller and coil overs
    • Apologies for the long read My R34 GTT was up for sale at the beginning of spring due to a few repairs creeping up. The strut tops needed replacing, roof and bonnet (hood) painting (yay for 3 stage pearl) and the underside stripped and treated. I sold the car which allowed me to be in a much better place financially. Leading up to the sale I was already thinking about the replacement. In an ideal world it needed to be a good all-rounder. Something I can mess around with, modify, do track days, do the school run, go on long drives etc.  Options included but not limited to... Laurel C35, Evo 8/9, Civic FD2, Impreza Hawkeye, Aristo and even an Audi S4 Avant (I've already got the Mazda 6 wagon). But there was always one car at the top of the list The Toyota Mark ii JZX110 I found an advert on a Facebook group for an example in Japan, from a seller called Jon at Rising Sun Exports. A few messages back and forth and Jon calls me from Yokohama one morning (or afternoon in his case). He briefly explained the import process, the costs involved and a repeat of the advert. After much deliberation, the price was agreed and the sale was locked in. I've never imported a vehicle so I jumped into the unknown head first. The money transfer was completed through wise.com (fees apply), very easy to use and the money was with him within a day or two.  The car suspension was raised for the vessel and the car dropped off at the port. It was 7 weeks later when the bill of lading was received and the freight invoice sent to me, followed by the export certificate a couple of days after (both digital copies) In the mean time the port had been in contact. I needed an agent to deal with the NOVA (notification of vehicle arrival) along with the tax/duty invoice, this was £75.00. The port also had a fee of £100, I'm guessing to cover the cost of the 10 day 'free storage' and for moving the car off the boat etc. They need a copy of the vehicle invoice, freight invoice and export certificate to allow the vehicle to pass through customs. The vessel arrived on Tuesday 5th August, the tax/duty invoice was generated and sent over. This is generally tax 20% and duty 10% of the vehicle value. Although the invoice came in at a higher amount than I had calculated. Once HMRC had received the payment the vehicle could be released from customs. I thought once the tax/duty was paid you could collect at any point, that's not the case. Your agent will need to book a collection slot, I requested Thursday 7th which was accepted, with a 9:00am slot allocated. It was a 5:00am start from Norfolk heading to Southampton. We eventually found the compound, upon presenting the bill of lading and some ID they released the car (they drove it out of the compound to the front ready for us to load up). The email from the port stated each slot had a 10 minute window, which seemed abit farfetched but the staff said it's not a strict rule. We were there for approx. 30-40 mins in total. A week prior to collecting I contacted my garage and explained the situation, I was able to get an inspection slot that afternoon. For the registration, DVLA require the car to be insured, for this I used a company called Adrian Flux who can insure the vehicle using the VIN number. 
    • Hey guys, looking for these side skirts if anyone can help me out. 
    • Wife and I are still looking for a new home. One condition was a large enough garage for a full-size lift in one bay. Now if only we could find something... We've been looking for almost a year now.
    • Thanks everyone for the ideas! Sadly, ramps are a no go for me. With young kids at home, I do most of my work late at night while they're sleeping. Starting the car multiple times wouldn't be a great idea.  I'll go see one of those new long reach low profile jacks and take a couple measurements to see if they will fit.   
×
×
  • Create New...