Jump to content
SAU Community

Recommended Posts

Lel discussion time.

I run BCPR6ES-11 (1.1mm gap) with Yellow Jackets. Standard RB26 motor standard boost. Works fine, no issues, even when overheating during a track day.

If you're on a budget or have a standard engine, yellow jackets are fine.

From the consensus around here, if you're pushing you're engine towards 300kW, best to go OEM coils and 7ES plugs.

^^lol. You can lookup the SAU yj feedback thread if u can find it. I wonder where it went. Rolls eyes. To op, buy what your budget allows for but remember you get what you pay for and poor man often pays twice. Splitfires can be found for around 550 and OEM around the 600 mark. The decision is yours. China or Japan.

You can get YJs for only $400 including express post. I have them in stock and post daily. These are actually really good for high boost applications despite what others say.

OEM and Splitfire are too pricey due to middlemen markups and over-inflated wholesale prices.

YJs have been on the market for around 7 years now. Ive sold heaps to thousands of people all over the world.

There's tons of positive feedback on them. Here's my ebay feedback to prove it - see here

Nothing but good comments on the YJs and Im also a trader here on SAU.

Buy YJs direct from the manufacturer (ME) and save your hard earned for other mods.

I am a trader on SAU and I have every right to sell and promote my products.

in the appropriate 'for sale - traders' section. Keep flogging your horse in the open forums and expect to get hosed; pls no more tears when you do.

To OP re spark plugs, everyone says use coppers and just change them more, but I've had less misfires/smoother idle with iridiums, and they've last me frkn years, and work out better value. So not really any reason to pay less and have to keep changing plugs IMO, but up to you of course.

in the appropriate 'for sale - traders' section. Keep flogging your horse in the open forums and expect to get hosed; pls no more tears when you do.

I have no idea what you are talking about? Im not into flogging horses? Sounds gay,

To OP re spark plugs, everyone says use coppers and just change them more, but I've had less misfires/smoother idle with iridiums, and they've last me frkn years, and work out better value. So not really any reason to pay less and have to keep changing plugs IMO, but up to you of course.

My tuner told me to get PFR7G- for best results with tune. Done about 2 years on them so far.

Middle men, manufacturers? I think these guys are ripping off your brand mate. lol. hope u got a patent on that colour. They even offer 24 month quality warranty.

http://www.ebay.com.au/itm/222124001105?_trksid=p2055119.m1438.l2649&ssPageName=STRK%3AMEBIDX%3AIT

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...