Jump to content
SAU Community

Recommended Posts

I have had over 25 cars in my life BUT the windscreen reflection on my 34 is something else, never had anything like this before. Had to change the undies a couple of times when I got home, lol

Always drive with sunnies on during the day.

I drive a lot early in the morning on a bendy road, come out of, or into a corner into the sun and the road disappears, I mean , gone! white out!

Cleaned inside and out, run the washers when it starts to look dirty ish, use the sun visor and still scary. :yes:

I put a black mat out of the Tiida on the dash and that helps a lot, 50% better but that goes where it wants when you accelerate hard . Just ordered a R34GTR dash mat and and I am sure it will help the glare.

Just wonder if some type of tinting could help or maybe it has been used and is the problem because it has scratched up or something ????

Funny you brought this up. I had the exact same thing happen today, first time ever I was driving blind.

The windscreen just needs a proper clean. Sometimes you need to re do it over and over again until streaks and glare are gone.

What do you use to clean your inside? Most products leave a film behind that will intensify glare.

Hi Peter,

Use - 0000 fine steel wool you can get from Bunnings on the outside of your windscreen.

Give it a good rub over.

Then use Rainx following instructions.

Lastly get a 10-15cm sun strip for your front windscreen.

  • Like 2

Funny you brought this up. I had the exact same thing happen today, first time ever I was driving blind.

The windscreen just needs a proper clean. Sometimes you need to re do it over and over again until streaks and glare are gone.

What do you use to clean your inside? Most products leave a film behind that will intensify glare.

I have to say , driving blind(not drunk) is one scary Mother f er

Some of the protectant products for the dash are too shinny, I think the angle of the windscreen and how close it is to the dash might also play a part ?

I have some glass polish and I will try it in the morning and see how that works ?

I have the Bosch GEX 150 Pro sander/polisher and all of the different microfibre cloths, pads, polish and a glass cleaning kit. Think I will have to get serious with it :)

Just did the drivers side earlier this morning and went for a run and it is a bit better but the mat I covered the dash with works the best to help stop the reflection.

I will have the full R34GTR dash mat coming early this week and I will do a full windscreen clean and polish and see how it goes.

The windscreen is only 1 hand width away from the dash at the front of the dash, on the Tiida, it is 1 hands width close to the windscreen and I have no reflection problem, I just wonder if the dash being so close to the windscreen could cause the reflection ?

This is why I HATE silicon on the interior.

Way too much glare.

Also, watch the glass polishing, as it can cause warped vision if you create high/low spots.

Sun in your face is easy, just drop the sun visor but that reflective glare is something else. It is only very early or late driving, no problem at other times. Maybe my eyes are stuffed ?

But , I have never had this type of glare in any other car and have used Armor All?

In the 34GTR it makes everything disappear, bloody scary, better than a radar camera to make you drive UNDER the speed limit :)

Now I have to watch out if I polish it unevenly , cant win, lol

I use Repco Eclips , not as shinny as Armor All but still shinny

Going to get super fine 0000 steel wool later and also try the Rainx

But I think the Dash Cover will do the trick and it has the cut outs for the Aircon etc. I will take a couple of pics and post them, should have it tomorrow.

Thanks

cleaning the windscreen wont help much, its only good if its hazy and affects your vision at night, but doesn't appears to be the case

its probably just a fundamental design issue with the car - shape of the dash and the angles between dash, windscreen and driver's head

Plastidip the dash matt black :P.

Funny you said that , got the dash mat today and stuff me if it is not a Nylon or similar and Fn sparkles when the sun is on it. I will go for a run in the morning and see what happens.

Plastidip, have to look it up ??????

If it is crap I was thinking a matt black spray might be ok, not too sure how it would look or smell , should be OK when totally dry ?

cleaning the windscreen wont help much, its only good if its hazy and affects your vision at night, but doesn't appears to be the case

its probably just a fundamental design issue with the car - shape of the dash and the angles between dash, windscreen and driver's head

I think the design is the issue, windscreen very close to the dash and maybe since I am short I am closer than most ?

Funny you said that , got the dash mat today and stuff me if it is not a Nylon or similar and Fn sparkles when the sun is on it. I will go for a run in the morning and see what happens.

Plastidip, have to look it up ??????

If it is crap I was thinking a matt black spray might be ok, not too sure how it would look or smell , should be OK when totally dry ?

plasti-dip is a mat black spray.

AFAIK, its a liquified rubber.

You can pull it off fairly easily too.

plasti-dip is a mat black spray.

AFAIK, its a liquified rubber.

You can pull it off fairly easily too.

Probably do the job, but sounds like it might look a bit rough sitting on top of the dash ?

The dash mat is not a flat surface, some sort of carpet like material. Might try some black dye first if the mat causes glare, could always try the plasti-dip after if needed and if it comes off easily there should not be a problem if it looks a bit off :/

Let you know how the glare is tomorrow and take a pic, the mat itself looks , well OK ish but better than I thought it would look :)

Or you could use a pillow......jus sayin'

Hahaha, first car was a 1936 Dodge @ 15, needed 2 pillows,1 to lift me up to see over the bonnet and the other so I could work the clutch, brake and go go, so do not knock the worth of a good pillow or 2, lol

Had a run this morning but left a bit late but there was no glare with this dash mat, have to do it again earlier or later this arvo to get a true result

As you can see from the pics, there are cut out for the aircon and passenger airbags. So at least they put some thought in making it.

post-52098-0-28305500-1464651626_thumb.jpg

post-52098-0-87032900-1464651693_thumb.jpg

Oh gawds one of those mats. I'd spray the mat a, erm, matt colour to remove the shiny-ness.

That is the plan if it does not cut the glare down and with that Nylon type matting I guess it will not be too good. I think I will try the dye first to see how it goes ?

Have you had one of these, hard to tell when you see them on the web :/

Fit OK

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • For once a good news  It needed to be adjusted by that one nut and it is ok  At least something was easy But thank you very much for help. But a small issue is now(gearbox) that when the car is stationary you can hear "clinking" from gearbox so some of the bearing is 100% not that happy... It goes away once you push clutch so it is 100% gearbox. Just if you know...what that bearing could be? It sounding like "spun bearing" but it is louder.
    • Yeah, that's fine**. But the numbers you came up with are just wrong. Try it for yourself. Put in any voltage from the possible range and see what result you get. You get nonsense. ** When I say "fine", I mean, it's still shit. The very simple linear formula (slope & intercept) is shit for a sensor with a non-linear response. This is the curve, from your data above. Look at the CURVE! It's only really linear between about 30 and 90 °C. And if you used only that range to define a curve, it would be great. But you would go more and more wrong as you went to higher temps. And that is why the slope & intercept found when you use 50 and 150 as the end points is so bad halfway between those points. The real curve is a long way below the linear curve which just zips straight between the end points, like this one. You could probably use the same slope and a lower intercept, to move that straight line down, and spread the error out. But you would 5-10°C off in a lot of places. You'd need to say what temperature range you really wanted to be most right - say, 100 to 130, and plop the line closest to teh real curve in that region, which would make it quite wrong down at the lower temperatures. Let me just say that HPTuners are not being realistic in only allowing for a simple linear curve. 
    • I feel I should re-iterate. The above picture is the only option available in the software and the blurb from HP Tuners I quoted earlier is the only way to add data to it and that's the description they offer as to how to figure it out. The only fields available is the blank box after (Input/ ) and the box right before = Output. Those are the only numbers that can be entered.
    • No, your formula is arse backwards. Mine is totally different to yours, and is the one I said was bang on at 50 and 150. I'll put your data into Excel (actually it already is, chart it and fit a linear fit to it, aiming to make it evenly wrong across the whole span. But not now. Other things to do first.
    • God damnit. The only option I actually have in the software is the one that is screenshotted. I am glad that I at least got it right... for those two points. Would it actually change anything if I chose/used 80C and 120C as the two points instead? My brain wants to imagine the formula put into HPtuners would be the same equation, otherwise none of this makes sense to me, unless: 1) The formula you put into VCM Scanner/HPTuners is always linear 2) The two points/input pairs are only arbitrary to choose (as the documentation implies) IF the actual scaling of the sensor is linear. then 3) If the scaling is not linear, the two points you choose matter a great deal, because the formula will draw a line between those two points only.
×
×
  • Create New...