Jump to content
SAU Community

Recommended Posts

Piece together a Nismo style oil cooler kit for R34

I am trying to piece together a Nismo style oil cooler kit for my R34. seems like you can just buy the Nismo oil cooler ducts, and would be a lot cheaper to buy all the parts seperately and you get better result. Similar to what member HIRISK has done. Do you know what size Setrab oil cooler should I get?

  1. Setrab Oil Cooler (need correct size)
  2. Nismo Oil Cooler Ductings
  3. TRUST GREDDY GREX Remote Oil Filter Relocation with Thermostat
  4. TRUST GREDDY GREX Engine Oil Block Adapter
  5. Nomex/Kevlar braided hose
  6. -10AN Fittings

gallery_391_5153_48547.jpg

gallery_391_5153_246622.jpg

12814_Greddy_12401114_FS01-01@2x1446872913563d87515ef14.jpg

0269_2.JPG

  • Like 1

Lol. I have done EXACTLY this. haven't fitted it yet but have literally all the bits, except i didn't buy the nismo installation bracket kit as i was going to fab them out of steel instead, they wanted like 300 bucks just for a few bits of metal.

I have a Setrab series 6 25 row cooler, and it is slightly too tall to fit into the nismo ducting but was planning to cut and fibreglass the duct to fit it correctly. I will get some pictures tonight to show you what the issue is.

the setrab rows are much shorter than the older greddy style coolers, so 25 row setrab is slightly taller and longer than a 13 row Greddy/Trust one (which is basically the same core as the nismo one)

A25F22L_1_lg.jpg

 

 

0551_1.JPG

 

the greddy core is the same as the nismo one and I think would fit the duct perfectly. there are lots of 13 row coolers on the market with this older design so its an easier option. I went the setrab as I wanted the best cooler I could fit in there.

 

here is the genuine kit. the cooler is a 13 row one same as basically all the japanese brands, and now china copies.

55810-4_2.jpg

and here is what the nismo bracket kit looks like (21308-RNR45):

nengun-2669-05-nismo-oil_cooler_kit.jpg

Edited by burn4005

My oil cooler mission was all kinds of painful: http://www.sau.com.au/forums/topic/462362-oil-cooler-too-eager-faulty-thermostat-or-incorrect-temp-sensor-location/


Learnings:

- Do NOT buy a second hand kit

- Do NOT buy a Mocal sandwich plate for a street car (too much flow when cold) or if you want to run any sensors (who doesn't?)

- DO buy best quality hoses you can afford

- DO buy kevlar hoses so you don't have to stuff around with garden hose over it to stop rubbing, like I did

- DO install core in the guard instead of in inline with rad/AC/IC

Tl;Dr - Cheap out upfront and you'll pay manyfold later. Do your homework.

  • Like 2
47 minutes ago, Gts30t said:

Yep all that nismo stuff just made the ztune a piece of shit 

but most of the stuff on the Z-Tune isn't available to purchase.. 

9 hours ago, KiwiRS4T said:

Look at the construction of the Setrab cooler and you will see it is superior to the "Nismo" one.

Seems like Setrab 25 row is a bit too big and their 19 row is a bit too small... Fail

 

Greddy 13 row oil cooler size is L299mm x H185.4mm x W50mm . got the info from here

841705850_m.jpg

841705850_m.jpg

Edited by etang789

I have a 19 rows on a rb20 14psi/0.9b of boost and its just enough on track. I could duct it properly to gain some more cooling out of it but on a 30% bigger engine and much more power I don't think that will be a good idea even if ducted proprely.

 

Better take the 25 one and make it fit, at least if the goal is to track it. On the street the 19 rows will suffice.

  • Like 1

Pretty severe driving if you need an oil cooler on the street? I'm yet to see a street where you can sit on WOT for long periods...

I've got a 19 row Mocal on RB25DET Neo at 20psi and it seems to be fine on the track.

Pretty severe driving if you need an oil cooler on the street? I'm yet to see a street where you can sit on WOT for long periods...

I've got a 19 row Mocal on RB25DET Neo at 20psi and it seems to be fine on the track.



I have noticed that the oil temp gets up there on those really hot summer days in bumper to bumper traffic.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
×
×
  • Create New...