Jump to content
SAU Community

Recommended Posts

The bores and pistons do look decent, at least based on my limited understanding of combustion engines.

Still awaiting word from the engine shop on the head, loving the suspense :/ 

Here's the block:

30444420201_fe8550d1fb_c.jpg

  • Like 1

Still awaiting word from the engine shop on the head, loving the suspense :/ 

Got a positive verdict, thanks goodness. The head is being refreshed, they're just waiting on valve stem seals, shouldn't be too long. Might have a car again one of these days yay!

  • Like 1
  • 2 weeks later...

Finally got the car back. Based on a quick spin everything seems a-ok, no more bubbles in coolant, in fact the overflow is sitting rock steady at the max mark before and after a run now. Water and oil temps around 80 degrees at freeway speeds on a cool night. I need to do some more testing but so far very good yay!

  • Like 4
Care to let us know what it cost? PM if you want.

Of course, it ended up being around 3.5 plus another k for the new Mishimoto rad, all new water and heater hoses, diff oil change, second O2 bung and some other random stuff.

Lesson learned though, better take any coolant leaks very seriously.
  • Like 1
So when is the next track day to test it all out?

Good question, I've totally blown my budget this year (what budget) but keen to have one more run this year... Mates are heading up to Winton early Dec but I'm not sure if I trust the car quite enough for the hike just yet
7 minutes ago, V28VX37 said:


Good question, I've totally blown my budget this year (what budget) but keen to have one more run this year... Mates are heading up to Winton early Dec but I'm not sure if I trust the car quite enough for the hike just yet

Budget, what's that lol. I know what you mean. I went to Sandown last weekend, was going to make it the last track day for the year but my car didn't even manage to do a full timed lap before my turbo decided to let go. I spent the afternoon pulling the turbo off, it's currently being rebuilt.  I am now considering 1 more track day for the year. According to tampered motorsport website apparently there is a sandown track day on the 11/12. I may sign up for that once I have my car running again.

  • Like 1

Something random that I observed on the test drive last night is that my Defi exhaust temp gauge seems to read low. It never gets above 400 and is mostly 'fluttering' (slowly bouncing) around 300 for some reason. From memory it was 500-600 in normal driving before and 800+ on the track when pushed.

My initial reaction is that the probe must have taken a hit, however can anyone think of another explanation?


18 hours ago, V28VX37 said:

Finally got the car back. Based on a quick spin everything seems a-ok, no more bubbles in coolant, in fact the overflow is sitting rock steady at the max mark before and after a run now. Water and oil temps around 80 degrees at freeway speeds on a cool night. I need to do some more testing but so far very good yay!

Good work feel free to take a test drive down to the south east im about to put down an order on a nismo lsd tomorrow lol 

 

So was kinda curious to see how your car goes

4 hours ago, blah_blah said:

Good work feel free to take a test drive down to the south east im about to put down an order on a nismo lsd tomorrow lol 

So was kinda curious to see how your car goes

Sorry mate manic today and over the weekend but Sunday night could work? Unless you must buy tomorrow :)

4 hours ago, GTSBoy said:

Probe not pushed in as far as it was before.

It's a screw type so shouldn't have moved. Just went to the shops and the gauge barely moves from 2 (minimum reading) so something is amiss.

I'm pretty sure the guys at the shop welded the new O2 bung at the bottom of the front pipe with the EGT sensor still screwed in - could using a MIG/welder upset the (disconnected) probe?

Screw type thermocouple?  Never seen one.  Are you sure it's not just a plain sheathed TC that slips through a gland that you tighten?  That's what all the others I've seen are.  I've got mine pushed in juuuuust far enough to stick into the gas and get a decent gas reading (rather than a wall temp reading!) but not so far that it sticks way into the flow where it could cause unpleasant eddies/turbulence or perhaps burn off.

7 hours ago, GTSBoy said:

Screw type thermocouple?  Never seen one.  Are you sure it's not just a plain sheathed TC that slips through a gland that you tighten?  That's what all the others I've seen are.  I've got mine pushed in juuuuust far enough to stick into the gas and get a decent gas reading (rather than a wall temp reading!) but not so far that it sticks way into the flow where it could cause unpleasant eddies/turbulence or perhaps burn off.

This is what it looks like: http://www.defi-shop.com/installation/sensor/

egt_sensor.jpg

Mine was all assembled when I bought it, and just screwed into the bung added on top of the dump. Perhaps it's adjustable and has moved, I'll need to have a look.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...