Jump to content
SAU Community

GTS-T bucking/hesitating before it builds boost


Recommended Posts

  • Replies 76
  • Created
  • Last Reply

Top Posters In This Topic

So I've f**ked up along the way somewhere I changed it over I thought all went well, but won't start, cranks over but doesn't start tonight after work I gotta take it back out and double check my wiring were right positive to positive n negative to negative, there's a dash light on but I dno what it is

Link to comment
Share on other sites

That tells you when your Cat Coverter is blocked (there is a temp probe in the Cat that sets off the light at a certain temp)

Could it be a Cat problem? If that is coming up when you are trying to crank I doubt it. I'd only expect it to come up after the car is driven for a bit

Link to comment
Share on other sites

Are you hearing the pump run? If no it may be a wiring issue. I remember remarking at how brittle/fragile some of the fuel pump wiring was, maybe something has broken with those. If you are hearing the pump run I would pull the whole assembly back out and make sure everything is installed as it should be.

Link to comment
Share on other sites

I would confirm you are hearing the pump first. Then, if you are, pull the fuel line going to the fuel rail off and try to crank it and see how strong of a stream you have (you may want to just test for pressure).

If those tests "fail" then I would pull the pump out and inspect everything.

Link to comment
Share on other sites

Not sure if its the same on R32's but on my R33 if i turn the key about halfway between on and start and hold it there the fuel pump runs. Did so with Power FC anyway and the Link does it to however cuts the pump after a few seconds

Link to comment
Share on other sites

  • 2 weeks later...

What would happened when I try to start the car if I didn't put the hoses on correctly? I've checked I can defiantly hear the pump, but still won't start just cranks, thought that I've put everything back the way it was originally but don't understand why won't start. Any ideas

Link to comment
Share on other sites

Maybe you have the inlet and outlet hoses crossed? On the 32s that space is tight and they could easily get crossed. Easiest way to check is to pull fuel line going to rail and reroute it into a bucket. If you can crank it and fuel comes out, you know they are plumbed correctly.

Also, what condition is your fuel filter in? A clogged filter could give you grief as well.

Link to comment
Share on other sites

If you took the hoses off at the pump and aren't getting any flow, the issue is in the tank. If the pump was working correctly you'd have fuel everywhere.

To answer your last question, you want to focus on the hose between the filter and the rail, removing it from where it connects to the rail.

But start at the tank, it sounds like your pump isn't pumping.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • Neostead, I'm looking to have a custom surround done that also has a slot for a fog light. Would you be willing to create a 3d model I can buy or create and ship me the part or even provide/sell the current model for me to modify? Cheers
    • Did some maintenance on the MX5, did the engine oil and filter which was uneventful, then I drained the coolant to put in the new reservoir and a thermostat, reservoir took 5 minutes  The thermostat, well that took.........3 bloody hours, what a job, the issue was the 3 bolts holding it on, one was easy, 2 were hidden and required a few 1/4 drive extensions, 1 more than I had, and a 1/4 swivel, which I also didn't have, and a good amount of playing contortionist  Getting the 2 unseen bolts back on was a time consuming nervous nightmare, as I couldn't see where they went there was alot of stabbing and hoping for the best, trying to line up a 8 mm bolt straight, which you cannot actually see or get a hand in there, with a 1/4 swivel in the mix was a nightmare Anyways, it's done now, all burped out, and run up to temp a few times, happily no leaks thank Jebus After the thermostat fiasco I decided I need a few mental health days away from tools before doing the rest of the servicing on it As for the Dunnydoore, it had the aircon regassed and it has a clean bill of health, thinking about taking it out on Monday for a cruise down the coast to look at some houses if weather permits 
    • In other important race car news, instead of fixing the race car I changed the crank seals on the chainsaw, because wood burner Some damn tight (and lock tighted) m6 head bolts Who knew plastic crank cases were a thing! Quick tip, don't trust the youtube videos that say you can pull the old seals out with the head on in a husky 440e...not true, their crank seal tucks in behind the cover both sides. I'm not sure I'm a psychopath, but these things are damn loud....hope I can put all the bits back in the right place    Happily, it is now back to turning fallen trees into a combination of firewood logs and wood chips....just need a clear day to get into it properly
    • I've got 60L of e85 in there at the moment
    • Don't forget to make sure the tank is full to the brim before you try to replace the fuel pump too, that is an essential step.
×
×
  • Create New...