Jump to content
SAU Community

Recommended Posts

49 minutes ago, hy_rpm said:


Offt! shitbox
Almost a $50k build i wouldnt sell it not worth it

Is there a sneaky 3.2L stroker here you aren't telling us about?! ?

2 hours ago, Dose Pipe Sutututu said:

Decided to update my spreadsheet, turns out "cheap shit box project" isn't so "cheap" after all.

 

image.png.fad6f261960df98643a49e6f825b0bed.png

At least you arent in denial about what you have spent lol

20 minutes ago, admS15 said:

Im clearly doing it wrong... Still below 20k brah.

Not including consumables like brake pads and tyres.

Mine doesn't include tyres, pads, maintenance shit either :(

 

Keys were handed to a mate whilst it was in New Delhi. Safe to say the clutch, gearbox and engine seem to be working well.

 

  • Like 4
12 hours ago, V28VX37 said:

8/10

Would have been 9 but needs more gauges

More like needs a working tacho Hahah.. At present rev limiter is at 8300rpm soft cut and 8500rpm hard cut.

#becausehonda 

  • Like 1

Gifts run pre Lunar New Year (yes I'm Asian and no I won't go back to my country becasue I'm already here ?).

Still no time to throw it on the dyno yet but AFRs are in the low 11s and timing isn't anywhere even barely close to a stock map (actually used my old map and flatten the timing due to cams).

20180215_105354_Burst01.thumb.jpg.598d2b223ec53e5500a27610a90f44dd.jpg

  • Like 2
5 hours ago, Dose Pipe Sutututu said:

Gifts run pre Lunar New Year (yes I'm Asian and no I won't go back to my country becasue I'm already here ?).

Still no time to throw it on the dyno yet but AFRs are in the low 11s and timing isn't anywhere even barely close to a stock map (actually used my old map and flatten the timing due to cams).

20180215_105354_Burst01.thumb.jpg.598d2b223ec53e5500a27610a90f44dd.jpg

All i can say is LOL. 

5 hours ago, Dose Pipe Sutututu said:

Gifts run pre Lunar New Year (yes I'm Asian and no I won't go back to my country becasue I'm already here ?).

Still no time to throw it on the dyno yet but AFRs are in the low 11s and timing isn't anywhere even barely close to a stock map (actually used my old map and flatten the timing due to cams).

20180215_105354_Burst01.thumb.jpg.598d2b223ec53e5500a27610a90f44dd.jpg

All i can say is LOL. 

Without an idle correction rate vs. timing compensation table, getting the car to idle this smoothly wasn't easy! Had to pull a few Microtech tricks haha

 

  • Like 1
9 hours ago, Dose Pipe Sutututu said:

Without an idle correction rate vs. timing compensation table, getting the car to idle this smoothly wasn't easy! Had to pull a few Microtech tricks haha

 

y u no lumpy

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...