Jump to content
SAU Community

Recommended Posts

Thoughts on drifting daily car?

Hey guys I am looking to purchase a turbo car for my daily drive and I want to get into drifting. I am just curious, considering I've never done drifting before, how often do you run into issues with your car due to drifting? Would you say its a bad decision to drift in a daily?

Link to comment
https://www.sau.com.au/forums/topic/471159-thoughts-on-drifting-daily-car/
Share on other sites

I don't know personally, but it was my impression that drifting was the most brutal of all the "track car" setups. Dumping the clutch, throwing the car around sideways and running high rpms. I'm not saying don't do it, but I'd expect that every Monday after a session you'll be catching the bus for a day or two.
I'd love to see you do it just to see how you go, but I really think you might have troubles. Just my two cents...

My personal opinion is that it's never a good idea.

You'll be fine with having the occasional skid, or wet pan/peanut day but drifting is incredibly harsh on every part of a car.

Not only will you break critical items all the time, you will also strain everything else to the point of failure eg: suspension and bushes/clutch/diff/gearbox/engine/exterior and interior

Which all round results in a lower quality car which you started with. And as mentioned you'll probably need to catch the bus at times.. 

Agreed ... I wouldn't do it. Especially when your learning and if your car isn't up to scratch .... belting on it if something goes wrong, at best you'll prob get stuck at the track and have to get a tow home ... and then what. No car to do anything else with even drive around and get parts you need to fix the car

Drifting whether learning or at top level is brutal on your car

 

Edited by bcozican
  • 3 weeks later...

A bit of a late reply but having done i'll share a few bits. 

Drove and drifted an r33 gtst regularly for about 14 months with minimal issue. Do suspension mods only. Aside from a front mount and radiator don't touch the engine, thats when problems arise. Put a good clutch in from the start  

A good diff, suspension arms and diff and it will handle great. Keep spares of as much as you can. Namely axles, lca's and tie rods will make up most of your breakages. 

Watch your temps and regular maintenance and you should be fine for the most part, it's drifting though, eventually you will crash, break a gearbox and ruin a motor so be prepared.

 

  • Like 1

It will be tough while your learning. But in saying that 2 out of my 3 drift cars have been registered, driven to and from the track, and the first one was my only car.

I learnt to start small, too many people try too hard too quick and crash.

As above, don't do anything more than an exhaust and front mount etc power wise, even leave boost stock.

Car has to be in reasonable condition to start with, if you've bought something that's clapped out to start with it will give you problems

Get a good aftermarket temp gauge.

Don't go crazy with clutch choice (nothing too aggresive), take it easy clutch kicking and you'll have half a chance of driving it home.

Driving style will play a big part, its possible to drift without abusing the living crap out of your car. Again, this will be hard to do if your learning.

 

I did the 1300km (one way!) trip to QLD raceway, drifted for two days, then drove it home. My current car is pretty basic, RB20 powered (bolt on turbo, supporting mods, good tune @Unigroup Engineering), RB25 gearbox, jim berry clutch, cusco 2 way. Adjustable caster rods and camber arms, basic coil overs and thats about it.

 

 

 

  • 1 month later...

I can talk from experience as well, my R33 is my daily and is drifted quite regularly. 

My story will be similar to those above. I only have suspension, steering, interior and cooling mods really. Main things of note are oil cooler/power steering cooler/radiator & intercooler upgrade on a stock motor & turbo - my temperatures are never an issue, oil temps typically don't crack 110 degrees. 

I don't limiter bash, I don't clutch kick (well very very rarely), I rarely hand brake entry - 90% of my entries are with a little feint and weight transfer on the brakes. 

I'd say I'm pretty gentle on the car overall and the only part I have had to replace in the past 2 years are the HICAS arms. I went through a set of new genuine arms in no time at all so I've replaced them with a proper HICAS delete kit, hopefully problem solved. 

If you want to drift your daily and your a learner, or want to abuse the car... hmmm I'd probably buy a cheap 2nd car and drift that 

  • 1 year later...

Probably worth an update, so my daily drift car has done a big end bearing. Guess it was only a matter of time with no oil control mods done on the engine. 

Next  one will have pump, sump, restrictors, drain etc etc - hopefully no more spun bearings. 

On the plus side, still haven't broken any driveline or suspension components. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I don't think the shuffle can damage the turbos. It only happens at low shaft speeds and loads. It's just annoying (to some people - others are tickled by the effect) and it quite possibly reduces spool performance a little bit.
    • Oh dear. The panel beating needs to be done before the filler work. Do you have a photo of the dent before you started? Hard enough to not flex and only hit the high spots?  What do you mean it was just temporary? 
    • Can u check this way it works for power supply?
    • These coils draw 10amps that what i read online
    • I appreciate the detailed explanation, think I understand now. I spent the better part of last night reading what I could about shuffle and potential solutions. I had replaced the OEM twin turbo pipe with an alternate Y pipe that is separated further away from the turbo. The current one is from HKS and I had a previous pipe that was separated even further away, both have shuffle. I had heard that a divider can be welded in to the OEM pipe to remove turbulence, and figure that aftermarket pipes that are more separated would achieve the same thing. From what I read, most people with -10 turbos get shuffle due to their size, though it's a bit less common with -5s on a standard RB26. I think Nismoid mentioned somewhere it's because OEM recirculation piping is common in Australia with -5 cars. It seems that the recommendation tends to vary between a few options, which I've ordered in what I think is most feasible for me:  1. Retune the MAP or boost controller to try to eliminate shuffle 2. Install OEM recirculation piping 3. Something called a 'balance pipe' welded onto the exhaust manifolds. I don't know if kits for this are available, seems like pure fabrication work 4. simply go single turbo My current layout is as follows: Garrett 2860 -5s HKS Racing Suction intake MAF delete pipes HKS racing chamber intake piping hard intercooler piping,  ARC intercooler HKS SSQV BOV and pipe Haltech 2500 elite ECU and boost solenoid/controller HPI dump pipes OEM exhaust manifolds HKS VCAM step 1 and supporting head modifications Built 2.6 bottom end All OEM recirculation piping was removed, relevant areas sealed off I'll keep an eye out for any alternative solutions but can get started with this.  Only other question is, does shuffle harm the turbo (or anything else)? It seems like some people say your turbo shafts will explode because of the opposing forces after a while and others say they just live with it and adjust their pedal foot accordingly. 
×
×
  • Create New...