Jump to content
SAU Community

Recommended Posts

Thoughts on drifting daily car?

Hey guys I am looking to purchase a turbo car for my daily drive and I want to get into drifting. I am just curious, considering I've never done drifting before, how often do you run into issues with your car due to drifting? Would you say its a bad decision to drift in a daily?

Link to comment
https://www.sau.com.au/forums/topic/471159-thoughts-on-drifting-daily-car/
Share on other sites

I don't know personally, but it was my impression that drifting was the most brutal of all the "track car" setups. Dumping the clutch, throwing the car around sideways and running high rpms. I'm not saying don't do it, but I'd expect that every Monday after a session you'll be catching the bus for a day or two.
I'd love to see you do it just to see how you go, but I really think you might have troubles. Just my two cents...

My personal opinion is that it's never a good idea.

You'll be fine with having the occasional skid, or wet pan/peanut day but drifting is incredibly harsh on every part of a car.

Not only will you break critical items all the time, you will also strain everything else to the point of failure eg: suspension and bushes/clutch/diff/gearbox/engine/exterior and interior

Which all round results in a lower quality car which you started with. And as mentioned you'll probably need to catch the bus at times.. 

Agreed ... I wouldn't do it. Especially when your learning and if your car isn't up to scratch .... belting on it if something goes wrong, at best you'll prob get stuck at the track and have to get a tow home ... and then what. No car to do anything else with even drive around and get parts you need to fix the car

Drifting whether learning or at top level is brutal on your car

 

Edited by bcozican
  • 3 weeks later...

A bit of a late reply but having done i'll share a few bits. 

Drove and drifted an r33 gtst regularly for about 14 months with minimal issue. Do suspension mods only. Aside from a front mount and radiator don't touch the engine, thats when problems arise. Put a good clutch in from the start  

A good diff, suspension arms and diff and it will handle great. Keep spares of as much as you can. Namely axles, lca's and tie rods will make up most of your breakages. 

Watch your temps and regular maintenance and you should be fine for the most part, it's drifting though, eventually you will crash, break a gearbox and ruin a motor so be prepared.

 

  • Like 1

It will be tough while your learning. But in saying that 2 out of my 3 drift cars have been registered, driven to and from the track, and the first one was my only car.

I learnt to start small, too many people try too hard too quick and crash.

As above, don't do anything more than an exhaust and front mount etc power wise, even leave boost stock.

Car has to be in reasonable condition to start with, if you've bought something that's clapped out to start with it will give you problems

Get a good aftermarket temp gauge.

Don't go crazy with clutch choice (nothing too aggresive), take it easy clutch kicking and you'll have half a chance of driving it home.

Driving style will play a big part, its possible to drift without abusing the living crap out of your car. Again, this will be hard to do if your learning.

 

I did the 1300km (one way!) trip to QLD raceway, drifted for two days, then drove it home. My current car is pretty basic, RB20 powered (bolt on turbo, supporting mods, good tune @Unigroup Engineering), RB25 gearbox, jim berry clutch, cusco 2 way. Adjustable caster rods and camber arms, basic coil overs and thats about it.

 

 

 

  • 1 month later...

I can talk from experience as well, my R33 is my daily and is drifted quite regularly. 

My story will be similar to those above. I only have suspension, steering, interior and cooling mods really. Main things of note are oil cooler/power steering cooler/radiator & intercooler upgrade on a stock motor & turbo - my temperatures are never an issue, oil temps typically don't crack 110 degrees. 

I don't limiter bash, I don't clutch kick (well very very rarely), I rarely hand brake entry - 90% of my entries are with a little feint and weight transfer on the brakes. 

I'd say I'm pretty gentle on the car overall and the only part I have had to replace in the past 2 years are the HICAS arms. I went through a set of new genuine arms in no time at all so I've replaced them with a proper HICAS delete kit, hopefully problem solved. 

If you want to drift your daily and your a learner, or want to abuse the car... hmmm I'd probably buy a cheap 2nd car and drift that 

  • 1 year later...

Probably worth an update, so my daily drift car has done a big end bearing. Guess it was only a matter of time with no oil control mods done on the engine. 

Next  one will have pump, sump, restrictors, drain etc etc - hopefully no more spun bearings. 

On the plus side, still haven't broken any driveline or suspension components. 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...