Jump to content
SAU Community

Recommended Posts

34 GTR, came with BC External Reservoir coilovers, subframe collars and whiteline rear sway bar. 

Came with 275 cheap tyres, Achilles Sport something, 400 tread wear, not fantastic.

Car is 99% street driven and the ride is way too firm for that, on the track day I did, car wanted to understeer quite easily an low speeds, rear seemed like it had bulk grip. Stock arms so -1.5 front camber, -2 in the rear. 
 

Justjap/BC said don't change spring rates on BCs as they are not valved for that, I'm not sure if mine are 8/6 or 9/7 which is the 2 standard flavours. 

MCA recommends Street Performance (purple ones) with 11/5 spring rates. They're about 2k.  

Shock works says "our street setup" which is a bit cheaper but hasn't provided any idea on specs. 

Can I just go ahead and drop some lower rate springs in? How do I properly confirm current rates? 

Any reviews of MCA street performance in a GT-R? 11/5 seems like an odd spring combo and makes me think it'd want to understeer. 

Any info on what the Shockworks street setup is?

New shocks are cheaper than on roads for another car :)

With my R34 i ended up with MCA Reds with 12kg/5kg springs - dampers were valved for tarmac rally/hillclimb rather than circuit/track

Came from M-Spec stock suspension which was surprisingly jarring on sydney roads, the MCAs were an improvement in ride-quality both when driving quickly and at the speed limit.

I went with MCA as they had done speciifc model testing on the R34, where i believe shockworks' test car was a R32 GTR.

Another option to consider is PSS9 bilsteins which are a good choice off the shelf, and can be bought and serviced in Sydney by Heasmans

Some info might be useful from my thread.

 

Edited by JGTC

That's encouraging, that they were better VS standard suspension. 

 

When you say ride quality, what does that mean to you? 

To me it's primarily about how harsh the car rides over bumps/joins/imperfections in the road. 

Seems a little counter-inuitive.

Bad tyres, uncomfortable shocks, but you seem to want a great road ride that's also great on the track? There's only so far that is even possible.

MCA or Shockworks will do what you want however. Shockworks will be cheaper, but BC ER's aren't actually that bad and I'm not sure you'd notice some world of amazing difference, the changes are going to be subtle, there's no way around the fact that making it softer on the street will make it softer on the track.

Everyone has rave reviews about physically calling MCA and talking to them (Josh gets a good rap) so it's probably worth just picking up the phone with an idea of what you really want out of this particular car. The cost is high but everyone seems to say its well worth it in the end.

BC ER coilovers are the wrong choice for street driven comfort period.

BC specify that the ER's are designed for 100% track use only so I don't believe you'd be satisfied after changing spring rates.

A set of BC BR-RS (Rubber top mounts) would be the way to go in regards to street comfort out of your BC options.

Spring rates like that will give you three things:
1 Understeer.

2. Good traction.

3. Harsh front end.

Essentially if you don't get bored understeering around corners you will get good traction if you can ever get on the gas.

If you look at Nismo S tune spring rates you will see they are higher on the rear than the front. 6.0kg/mm front 6.7kg/mm rear.  Much more sensible rates.

Did notice that, which seems to make more sense to me given the car is also dialed for more rear camber from factory. 

Everybody tells you there setup is best =\ 

Not easy to just go for rides in everyone elses GT-Rs when you're not in the CBD. 

Spring rates are only part of the puzzle. What's the valving like? What viscosity fluid is used?

Over the years I have run stock V spec, Nismo S and R tune... then finally cracked it and did it properly. 14 kg/mm front springs and 9 kg/mm rear but the valving in them is far from "normal". Around town and bumpy "shit Sydney roads" it soaks all that stuff up MUCH better than the 3 gastric junk setups before it.

Long story short, looking at one part of the shock is pissing in the wind and a waste of time!

 

  • Like 2

I had shockworks in my R34 GT-T, definitely not bad at all comfort wise with their standard rates. I wouldn't call it comfortable however.

Have had a set of BC V1s in my previous car and ridden in countless cars with BC BRs, only purchase these if you have $1300 to spend. If you're spending $1300 on coilovers for a R34 GTR I think you need to reassess your priorities. I see countless 50k+ builds running BCs and cry a little.

I've driven a MX5 with X-R coilovers with their 'Tarmac' spring rates and was pleasantly surprised with comfort and performance. Going off this I can only guess that X-C would be significantly better. 

TLDR

- Buy BC BR if budgeting ~1300, don't cry when they ride shit.

- Buy MCA X-C with suitable spring rates if you want decent comfort (or fork out for reds), just talk to MCA.

 

  • Like 2
6 hours ago, ActionDan said:

"MCA recommends Street Performance (purple ones) with 11/5 spring rates. They're about 2k."

Sorry mate, don't know how I missed that. Is purple their new blue? Blue was about $1,600 from memory.

maybe have another look at their site too as they've recently changed their offerings

  • Blues
  • Street Essentials
  • Street Performance
  • Street Ultimates
  • Race Prime
  • Race Red

with a number of default spring options, with Comfort recommended as 9/4 as opposed to the 11/5 for performance

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...