Jump to content
SAU Community

Wich skyline do you like most

Slap
 Share

Recommended Posts

BK Grand Master

BK

Posted
Posted

Survey for who ? People that have never owned or driven a GTR to make an.opinion on what they think is better ? Funny you say that "WICH" Skyline you like the most in the vid as 32 vs 34 when the first one is a 33.

 

 

hardsteppa Grand Master

hardsteppa

Posted
Posted

I like the R37 the most...i'm ahead of my time. My favorite features would have to be the Whisper Mode and the gun turret that follows wherever the driver looks.

Oh wait...no that's Blue Thunder, my mistake..

  • Like 2
Ben C34 Grand Master

Ben C34

Posted
Posted

For me it's r35, then 32, then 34 then 33.

Based on feaures and development, and the fact (actual fact) and r34 looks  better than 33 so that should explain the order.

mind you if someone gave me any gtr I wouldn't complain.

  • Like 1
The Bogan Grand Master

The Bogan

Posted
Posted
1 hour ago, r32-25t said:

There is definitely something special about the r31 gtsr, wonder if there’s any pink ones 

Here's one, 4 door GX auto though.

Looks better than your 33 though......jk.......but seriously........

I bet a flat capper has wrecked it.

2013 post > 

 

post-78013-0-65023600-1385202159.jpg

  • Like 1
The Bogan Grand Master

The Bogan

Posted
Posted
18 minutes ago, r32-25t said:

Oh thats awesome definitely looks better then my r33 cause it actually exists 

Crap, I mistook you for Dosepipe.

You guys all look the same to me.....................................................unnamed.gif.212e0c9ce87b9b89cd40a5e14f1f4bc7.gif

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      What accelerator cable can be used with greddy plenum

      By Duncan · Posted

      I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...