Jump to content
SAU Community

Help installing pod filter

020king
 Share

Recommended Posts

020king Apprentice

020king

Posted
Posted

Hi, I need help changing my stock air intake to pod. I was in the middle of removing the stock air box. Iv unbolted everything but can't seem to remove the maf from the hose. Iv undone the jubilee clip but it's not budging. Pic has been attached and I will resume once the rain has stopped. Any help is appreciated! 

20191109_145005.jpg

Link to comment
https://www.sau.com.au/forums/topic/479136-help-installing-pod-filter/
Share on other sites
020king Apprentice

020king

Posted
  • Author
Posted
38 minutes ago, Murray_Calavera said:

You say you've unbolted everything but in the picture there are still many bolts?

Go forth and remove bolts, this should be a very simple job. 

Do I need to remove the 4 gold bolts circled in red? Everything else is unbolted and iv been trying to remove it via from the hose circled in green if I can free it from there then the whole box and maf will come out. Thanks for the help 

20191109_180507.jpg

GTSBoy Grand Master

GTSBoy

Posted
Posted

They're holding the AFM to the airbox. Seeing as you've loosened the hose clamp, if you want to slip the AFM off the inlet pipe, to make it easier to work on the AFM to airbox on the bench/lap/whatever, then just pulling the AFM out of the hose would be a good start.

020king Apprentice

020king

Posted
  • Author
Posted
2 hours ago, GTSBoy said:

They're holding the AFM to the airbox. Seeing as you've loosened the hose clamp, if you want to slip the AFM off the inlet pipe, to make it easier to work on the AFM to airbox on the bench/lap/whatever, then just pulling the AFM out of the hose would be a good start.

Will I have to remove those 4 bolts anyway to connect that side to the hks air intake? 

Ben C34 Grand Master

Ben C34

Posted
Posted

Just remove the bolts. Sounds like you reallly want to!

Yes you will have to remove them to attach the pod, that should be fairly obvious.

then sit back and enjoy the pointless mod you have just implemented.

Murray_Calavera Mentor

Murray_Calavera

Posted
Posted

You seem to be scared of undoing those 4 bolts.

You also seem to have hit a road block.

My advice would be, remove the bolts. You might find it helps. If it doesn't, you'll be surprised that you can do them back up. 

Don't be scared to have a go and try things. If your paranoid, take lots of photos and put the parts/bolts into resealable plastic bags and label them.

020king Apprentice

020king

Posted
  • Author
Posted (edited)
On 10/11/2019 at 8:07 AM, Murray_Calavera said:

You seem to be scared of undoing those 4 bolts.

You also seem to have hit a road block.

My advice would be, remove the bolts. You might find it helps. If it doesn't, you'll be surprised that you can do them back up. 

Don't be scared to have a go and try things. If your paranoid, take lots of photos and put the parts/bolts into resealable plastic bags and label them.

 

Thanks everyone for the advice. I couldn't get to 2 of the bolts as those gold bolts can only be removed from the opposite side. I was scared of applying too much pressure on the hose and tearing it so in the end I decided to get 2 big flat head screw drivers and pry away and it came off easy. After that it was all good and its now on the car. The car sounds amazing can hear the turbo spool up loud like a jet. ???

Edited by 020king
The Bogan Grand Master

The Bogan

Posted
Posted
1 hour ago, niZmO_Man said:

Shame it's making less power now.

But it sounds like a jet..

OP, put on cover, it will still sound whoosshhhy, but be more legsl and less hot air

 

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MissMintyR33
      R33 persistent issues. P/steering and lag/misfire

      By MissMintyR33 · Posted

      I thought that might be the case, thats what I'll start saving for. Thanks for the info 
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • jtha7
      Strange issue RB25DET wont start

      By jtha7 · Posted

      Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • GTSBoy
      Freddy Plenum vs Genuine options RB25

      By GTSBoy · Posted

      My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
    • Murray_Calavera
      R33 persistent issues. P/steering and lag/misfire

      By Murray_Calavera · Posted

      There is a really fun solution to this problem, buy a Haltech (or ECU of your choice) and put the MAF in the bin.  I'm assuming your going to want more power in future, so you'll need to get the ECU at some stage. I'd put the new MAF money towards the new ECU. 
×
×
  • Create New...