Jump to content
SAU Community

Recommended Posts

Parts List

 

OEM Nissan Parts:

 

R33 Gtr Rb26dett Engine

R33 Gtr 5 Speed Transmission

R34 Gtr Front Subframe

R34 Gtr Front Lower Control Arms

R34 Gtr Front Upper Control Arms

R34 Gtr Front Knuckles

R34 Gtr Steering Rack and Pinion

R34 Gtr Front Sway Bar

R34 Gtr Front Coilovers (Ohlins)

R34 Gtr Front Axles

R34 Gtr Front Brakes

R34 Gtr Front Brake Lines

R33 Gtr Front Prop Shaft

R33 Gtr Main Prop Shaft

R34 Gtr Rear Subframe

R34 Gtr Rear Diff

R34 Gtr Rear Axles

R34 Gtr Rear Control Arms

R34 Gtr Rear Hubs

R34 Gtr Rear Brakes

R34 Gtr Rear Brake Lines

R34 Gtr Rear Sway Bar

R33 Gtr Attesa Pump

R33 Gtr Attesa Fluid Reservoir

R33 Gtr Transmission Crossmember

 

 

Aftermarket Parts

 

Engine:

HKS 2.8L Rotating Kit

HKS Valve Springs

Tomei Pro Cams

HKS Timing Belt

HKS Cam Gears

N1 Oil Pump

N1 Water Pump

HKS Gaskets

G-Force Silicone Coolant Hoses

Reworked R34 N1 Turbos

Tomei Turbo Dump Pipes

Apexi Downpipe

Nismo Flywheel

Nismo Clutch

 

Fuel System:

AEM In-tank Fuel Pump

Aeromotive Fuel Pressure Regulator

8 AN Fuel Lines

Aluminum Fuel Rail

GM Flex Fuel Sensor

 

Chassis:

Nismo Engine Mounts

Nismo Transmission Mount

HKS Exhaust

Chase Bays AN Power Steering Hose

R34 Gtr Aluminum Radiator

 

Electronics:

Adaptronic eMod004 ECU

Full Race ETS-Pro Diff Controller

Wiring Specialties RB26 Universal Pro Engine Harness

Greddy Boost Control Solenoid

Depo Wideband 02 Gauge

R33 Gtr Drop Resister

R33 Gtr Ignighter

 

Misc:

HKS M35 Spark Plugs

HKS Oil Filter

Royal Purple Engine Oil

Royal Purple Gear Oil

Royal Purple ATF

3D Printed MAF Delete Pipes

Sprinkle of Magic

 

 

 

 

 

  • 4 months later...
  • 5 months later...

I'm curious to know whether the OP had to modify the chassis legs to clear the front axles. It would be a show stopper in NZ. See the raised section on the BNR34 chassis:

tempsnip.png

Edited by NZ-GTT

 I found that the GTR subframe sits approximately 2 inches lower in the car than the GTT sub frame.   So what I did was box the end of the sub frame mounts adding that additional 2 inches and contouring it to the frame of the GTT.   Then I drilled 1 inch holes through the existing frame rails vertically and sleeved them with a .060 wall tube.   I attached the sub frame to the existing frame rails using 1/2 inch grade 8 hardware.   Keep in mind that you also need to modify the driver side floor pan as well as the driver side frame rail to except the GTR transmission mount.   

C003EE28-3D5B-4A4C-8E22-C43BECEF2B24.jpeg

B6E4093D-EA5B-48ED-8A41-4A47C16A7788.jpeg

420BFFF6-6CD6-4258-B345-87475C14A8D5.jpeg

089828ED-F4CE-4066-97CB-7C2D5D07C532.jpeg

15FA9475-3301-4020-9637-9D8E9F6C5595.jpeg

ECCE8B9D-E209-49CA-9C22-FB531D2D8345.jpeg

8F71C6AF-9942-4297-A24D-2F4E77846DBD.jpeg

9B20962A-B9F0-47CC-99C2-BE0ADB207C50.jpeg

B12AAD06-0A81-44F1-AF1C-E86B1177CE2A.jpeg

80B366A1-CC4D-4C9A-9307-8131B3AE067D.jpeg

5905F6B1-1713-4396-A647-B49B0D05C7EE.jpeg

94EB83E6-B13C-4413-96E7-92904C7556B9.jpeg

B18C9BE4-F386-4E0B-BF2C-AF1A56CC0BEF.jpeg

54557C5C-1647-4B1C-A8D5-15C81F45BC6F.jpeg

C498A7FB-5A78-4011-9C46-5EE305A5CE37.jpeg

F85E88C7-E5FB-4C64-B696-F17F17937EF4.jpeg

  • Like 4

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...