Jump to content
SAU Community

Recommended Posts

Don't worry about the shifting guide. You can change up at any speed between idle and redline. The only question after that is whether it will have enough torque to swallow much throttle opening in the next gear> RB20s have little torque, so the answer to that question will be "no" unless you're above about 3k rpm. And just to the right of the speedo is the gauge that will tell you about that.

The km to mile conversions are correct enough. Everyone since forever has treated the conversion as 40=60, 50=80, 60=100 and 70=110, to within the accuracy that matters.

For efficiency shift based on the peak efficiency RPM, shift just past the peak efficiency point while maximizing load without encountering high load enrichment so you sweep through the efficiency sweet spot. Looking at the gearing of the GTRs it looks like you want to be shifting at 3000 RPM so you drop down to ~2000 RPM when accelerating. Hold the engine right around 50-60% throttle if this is an NA engine or right at atmospheric pressure for turbo engines for best results.

For cruising pick the highest gear that doesn't have you exceeding the accelerating throttle condition. As for the best speed to cruise at, something high enough that you aren't running below 2000 RPM and something low enough that you don't exceed 3000 RPM.

  • Like 1
3 minutes ago, joshuaho96 said:

It's simple, it's the condition where you are accelerating with the throttle.

How do you accelerate without using the throttle... unless rolling down a hill? ?

3 minutes ago, Piggaz said:

How do you accelerate without using the throttle... unless rolling down a hill? ?

Very carefully?

Jokes aside the point is that lugging the engine at 1500 RPM and WOT to cruise is going to actually be quite inefficient even if the pumping loss is minimized. It's better to cruise at 2500 RPM with less throttle. The exact numbers are going to vary by engine but the principle is the same.

1 hour ago, joshuaho96 said:

Very carefully?

Jokes aside the point is that lugging the engine at 1500 RPM and WOT to cruise is going to actually be quite inefficient even if the pumping loss is minimized. It's better to cruise at 2500 RPM with less throttle. The exact numbers are going to vary by engine but the principle is the same.

Can you explain how you came to this conclusion? 

I am interested in the math and any other data you are relying on to make this statement. 

  • Haha 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...