Jump to content
SAU Community

Recommended Posts

Hi I just recently purchased a r33gtr and looking to get it tuned on 98 as I don’t want to go e85 I was hoping for 380kw atw on 98 do you guys thing it’s reliable to achieve this power with these old turbos mod list below

Starting with r33 block, r33 crank with n1 oil pump, eagle rods,wiseco pistons, arp main studs,acl race bearings, tomei 260 deg pon cams, cometic head gasket.

Trust t517z turbos wiyh trust hard pipe kit

Trust race intercooler, hks dump pipes and 3in exhaust

R33 twin synchro box with twin plate clutch.

Sard fuel pump with 720cc injectors and billet fuel rail, Sard fuel pressure reg

Brake vacuum chamber

Apexi power fc with z32 airflow meters

Trust boost controller, and turbo timer

Edited by Berksgtr
Link to comment
https://www.sau.com.au/forums/topic/480867-400kw-goal/
Share on other sites

For reference, back in 2011 my 33 gtr with a built motor, good head t51r, full fuel system 1000cc injectors, and everything that should go with it was making 422kw on 20psi with 98

before going the full fuel system with surge tank and extra pump and to 4” exhaust, I think we maxed out out at 401 from memory.

Best bet would be to look through the dyno section for something with similar mods to you to get a reference of what to expect.

the end of the day a dyno is just numbers that can be fudged either way. True test of power is 1/4 mile

Link to comment
https://www.sau.com.au/forums/topic/480867-400kw-goal/#findComment-7937297
Share on other sites

Thanks for the replies I just bought the car last week I know it’s an old set up I’m be holding the car for a long time and will change things gradually Ben c34 what needs work any recommendations as I don’t know which direction to go thanks

Link to comment
https://www.sau.com.au/forums/topic/480867-400kw-goal/#findComment-7937310
Share on other sites

46 minutes ago, Berksgtr said:

Thanks for the replies I just bought the car last week I know it’s an old set up I’m be holding the car for a long time and will change things gradually Ben c34 what needs work any recommendations as I don’t know which direction to go thanks

Immediately just lose the turbo timer so it doesn't give you problems one day. For the rest just try to track down a good tuner and post up the results!

Link to comment
https://www.sau.com.au/forums/topic/480867-400kw-goal/#findComment-7937315
Share on other sites

Hang on, so does the car already have that list? Or is that to purchase?

 

No sane person would buy a power fc new nor those injectors considering the substantially better options available now. . If you already have them it's a different story.

 

 

And as above lose the turbo timer.

  • Like 1
Link to comment
https://www.sau.com.au/forums/topic/480867-400kw-goal/#findComment-7937321
Share on other sites

Haha yeh wow. Genuinely had to check if this post was from 2003 ?

 

OP, if your car already has those mods then just get the car tuned and be happy with where it ends up knowing that there is plenty of money to be wasted in the future chasing more. 

  • Haha 3
Link to comment
https://www.sau.com.au/forums/topic/480867-400kw-goal/#findComment-7937324
Share on other sites

3 hours ago, KiwiRS4T said:

Immediately just lose the turbo timer so it doesn't give you problems one day. For the rest just try to track down a good tuner and post up the results!

Why get rid of the turbo timer? I thought they were a good thing for turbo engines to let them sit for a bit after driving before shutting off the engine.

Link to comment
https://www.sau.com.au/forums/topic/480867-400kw-goal/#findComment-7937328
Share on other sites

2 hours ago, nouveau_poor said:

let them sit for a bit after driving before shutting off the engine.

And this is something that you cannot do for yourself? After all, it only needs doing if the car has been working the turbo a bit hard in the last couple of minutes before stopping. It hardly needs to be run to cool down on about 95% of stops.

Link to comment
https://www.sau.com.au/forums/topic/480867-400kw-goal/#findComment-7937331
Share on other sites

@Berksgtr It'll get close to 400 rwkw or 380ish awkw on 98. T517 is rated closely to -5s. Unopened 26s have hit that target. It'll just be a tad laggy by todays standards. Will still be good. Gotta start somewhere! Congrats on the car :)

Link to comment
https://www.sau.com.au/forums/topic/480867-400kw-goal/#findComment-7937338
Share on other sites

7 hours ago, GTSBoy said:

And this is something that you cannot do for yourself? After all, it only needs doing if the car has been working the turbo a bit hard in the last couple of minutes before stopping. It hardly needs to be run to cool down on about 95% of stops.

fair enough sure, but why get rid of the timer if he's already got it? The other post sounded like the timer itself would cause an issue.

Link to comment
https://www.sau.com.au/forums/topic/480867-400kw-goal/#findComment-7937354
Share on other sites

Can attest to the shittness of turbo timers, I had one in the Skyline as a young pup. Caused all sorts of issues from not starting, to not switching off when the countdown reached 0, to being a parasitic drain on the battery, etc. Even after pulling it out, the loom has been hacked into, there's no making that reliable again. Its one of the reasons I undertook a complete rewire of my car.

 

Stupid things. Feel embarrassed to have had one. As GTSBoy says, try to think of the last time you boosted your car hard and then switched the engine off. It just doesn't happen, there is always 1 or 2 minutes of sedate driving before you park up that is far more effective than 30 seconds of idling. Superbly ricer modification.

  • Like 2
Link to comment
https://www.sau.com.au/forums/topic/480867-400kw-goal/#findComment-7937363
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You know what, I am enjoying your updates, but I have to say it is pretty poor form to walk into a shop that is paying for space and stock on the floor, try all their seats to work out what you are happy with, then buy somewhere else. If everyone did that the shop will be out of business with no opportunity for anyone to try a seat before buying. 👎  
    • Good work, and thanks for posting up your solution for future people!
    • Yeah mate that’s the plan, I just want something I can have fun in and work on during weekends.  There’s really only 1 road fit to drive the car on and luckily is been redone recently.  I do want to tune it next year sometime, no dynos here so I’m looking at an ECU that can be remote tuned. 
    • Initially I thought having a pair of Recaro seats would be a big bonus, it turns out these do get a little uncomfortable on long journeys (my fault, not the seat). I had a look through the GSM Performance website at reclining seats and booked an appointment to visit their show room. I got the Recaro Sportster CS for the R34 from here, was very happy with the service received so of course a re-visit was in order. Unfortunately the two Corbeau seats I had chosen aren't on display but they had 4 other options available. Two seats dug into my back, one dug into my legs and the other was perfect. I also found out that Recaro seats use a larger bolt pattern so some adaption was required. Luckily GSM offer some universal adaptors that should solve this problem. I searched the interwebs for price comparisons and Corbeau themselves were the cheapest at £300 cheaper (for the pair). I asked GSM if they could price match, unfortunately they couldn't. I later received an email saying Corbeau would honour them the same discount, but the purchase was already made. I did however order the brackets from GSM, both arrived on the same day. I started with the passenger side seat, knowing this was going to be a little trial and error. There are 3 mounting holes at the front and 2 at the rear on these JURAN Racing seat rails.  With the adaptor brackets mounted, the allen cap bolts started to push into the seat, NOT GOOD!  The rear mounting holes lined up but there were issues at the front. The holes were 1/2 hole out, so the brackets got a tickle with the drill to modify the holes. The supplied bolts weren't going to be long enough and a spacer was needed to stop the adaptor bars from bending. A local fasteners company supplied be with some nylon spacers and longer bolts (M8x30, although these will be replaced with 35mm long shortly) A before and after I pre-drilled the front bracket before making a start on the driver's seat to save some time. And in no time at all that was in the car too. The all black seats have transformed the interior and these are MUCH more comfortable. The only downside with the new Corbeau seats is I sit a little higher, but I'll happily accept that over discomfort. The Youtube video can be found here: https://www.youtube.com/watch?v=wPyttKPktXA
×
×
  • Create New...