Jump to content
SAU Community

Recommended Posts

Hi folks, I hope to get some tips on removing front windscreen molding.

The top horizontal molding on my R32 has faded, so I order a new one.  Then I found out afterward the side vertical moldings need to come off before the top one can be removed.  Are there tricks or tips to remove the side moldings and reuse them again?  

Thanks in advance.

Yes I read that already, a few times actually, but it's just not that clear.  I mean, have you actually read it or you just copy and paste?

"disengage fastener from side molding by sliding lower two side molding clips" - I don't get it. Does that mean pushing the clips downward until they slide out from the bottom corner of windscreen? Also, there are 4 clips on each side according to the graph, so leave the upper two in place?

"remove side molding from fastener by pulling out lower end of molding" - Also don't get it. After the bottom 2 clips are out, I start pulling the side molding down? The top of side molding are 90 degree, won't that bend the molding by pulling down?

 

Given that the clips snap into place when installing, I'm pretty sure that they don't come out from under the trim. I think the sliding movement to release them just squishes them so that they flex and their tangs come out from under the lip they hook onto.

I've had them off about 20 years ago. Just fiddled around with the screwdriver until they released.

2 hours ago, TXSquirrel said:

"disengage fastener from side molding by sliding lower two side molding clips"

Unfortunately terminology is the likely problem here, I think, not to mention the GTR manual is translated from the Japanese and there is some 'JapLish' resulting.   The 'fastener' (PN 72725-04U19) referred to is a molded 'channel' that surrounds the left, right and top of the screen.   The fastener's purpose is to hold the windscreen molds in place via the clips mentioned.  It is embedded into the polyurethane windscreen seal at the time of windscreen installation.    

The clips have to be released from the fastener to take off the molds and the recommended method is using a shaped screwdriver between the mold and the windscreen to release the clips.     My interpretation is that the 'sliding' reference is actually to  'sliding' the screwdriver under the mold to release the clips.

In the same way, the 'pulling out lower end of molding' is actually a reference to moving the bottom part of the mold away from the windscreen after the clips have been released.    That has to be done carefully as to no bend the mold.     The mold could then be released at the top.

Anyway, having actually attempted this years ago I can say it's extremely difficult to release the clips without breaking them.     Unfortunately, the clips are no longer available from Nissan spare parts other than by buying a complete mold set.   They are available via the Heritage program, but quite expensive.

I bought complete new molding sets (front and rear) before the price went crazy and they've literally just been installed in my car.

 

 

    

 

 

Screen Shot 2021-04-01 at 4.27.57 pm.png

Thank you all for the feedback.  I bought the top molding first then read the manual, that's when I went oops. 

I thought I was being clever and saved money to find a website selling only the top molding, but looks I still need the whole molding kit so I wasted more money instead.  Just that my two side moldings are still in really good shape, so I'm spending extra money solely for the damn clips.

11 minutes ago, GTSBoy said:

No more than 4 years ago.

I bought my current GT-R in 2015. I reckon every piece of vinyl and plastic that I have bought since then has cost a comparative fortune.

So, six years?

Kudos sell the entire front screen trim and seal kit. I have done it and it's a pain in the arse. You will absolutely not save all of the coloured clips under the side trims - they will be brittle and just snap.

On 04/04/2021 at 8:28 AM, GTSBoy said:

Maybe.

I bought inner and outer door window strips for not too much not too long ago (like <2 yrs). Door hinges are still only ~$30 trade.

Inner door strips for white 32 arrived today. They are about $90 - $100 each.

It's the upper outer weatherstrips that are killer at over $1400 a side....Fk that !

  • 4 months later...
On 8/31/2021 at 5:08 PM, TXSquirrel said:

Can you please share how you did it?  

My molding was rock hard from age so I cut it in half somewhere in the center with an xacto knife, being careful not to destroy the molding fastener under. I then proceed to pull it out starting at the center working my way towards the side molding. If you look at your new molding, you'll notice that there's nothing that actually holds it into the fastener under the side moldings. Repeat with second part. 

If this is the first time you change a molding on your R32 or any older car, use a heat gun to soften it up as you pull it out. If you don't, it will tear often and you will need to remove the broken parts afterwards out of the molding fastener which is a pain. If you don't have a heat gun, just leave it out in the sun. I also put masking tape on the painted edge to protect it. Cheers. 

Edited by TurboTapin
  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • So stock ECU does not like anything above 10 psi?  That Nistune one is just for "try" if it will be any different, I know it need to be tune for that. I know but YOU may know about these problem but i/we dont. They few little Skylines here let alone people who know anything about tham so that is why iam asking here  
    • So now we have a radiator with no attachments whatsoever. It lifts up with a particularly tight spot between the drivers side air box mount and the lower radiator outlet, but if you've got this far you will sort that too. This is the lower mounts with the rad out so you can see where the rubber bushes go, it is a straight shot upwards Done! Assembly is the reverse of disassembly, with blood less likely to be shed.
    • Right, onto the second last trick. The Air Con condenser is mounted to the front of the radiator and stays in the car when the radiator is removed. There are 2x 10mm headed self tappers holding the top of the condenser to the radiator, remove those The bottom of the condenser is attached to the radiator with clips. You need to lift the condenser out of those clips and clear (up, then forward). f**ked if  could work out how to do that last bit with the front bumper on. I hope you can, and you share the trick.  Bumper removal probably deserves its own thread one day once I've recovered the will to live, but basically you need to remove the wheels, front inner guard liners (clips and 10mm headed bolts), the self tapper between the guard and the bumper at the rearmost point of the bumper (same as an R32 that bit), any remaining clips at the top/front of the grill, an absolute bastard design with a plate that holds the top of the bumper above the headlight each side (only 1 bolt which is tricky to get to, but the plate catches 2 places on the bumper and must be removed....carefully!) and push clips between the bumper and guard under the headlight. If you've done all that you will be faced with wiring for the fog lights on both sides and in ADM Q50 RS at least, 4 nasty tight plugs on the driver's side for the ADAS stuff. So, the clips at the bottom look like this on drivers side (looking from the front) And on the passenger side (also from the front), you can see this one is already out Clearance on both of these are super tight; the condenser needs to move up but the upper rad support mount prevents that, and the radiator can't move down far because it is (rubber) mounted. Once you achieve the impossible and drop the condenser off those mounts so it does not stop the rad moving, you are good to go
    • OK, next the shroud needs to come off and there are a couple of tricks. Firstly, there is a loom from near the passenger side headlight to the fans, coolant temp sensor etc and there is no plug to undo.  In my case I was OK to leave the shroud on top of the engine so I just undid the passenger side fan plug and about 10 of the clips which gave enough free wire to put it aside. The fan plugs were super tight, the trick I used was a small falt screwdriver to push down on the release tab, then a larger flat screwdriver to lever the plug out of the fan unit....be careful with how much force you apply! If you need to remove the shroud altogether for some reason you will have to deal with all the plugs (tight) and clips (brittle)....good luck. I removed all of the clips and replaced them with cable ties that I will just cut next time. Also, in the Red Sport / 400R at least, the intake heat exchanger reservoir hose is bolted to the shroud in 2 places with 10mm headed bolts; so remove them (the hose stays in the car; no need to undo it at the t fittings down at the radiator lower mount. Once you've dealt with the HX hose and the wiring loom, there are 3x 10mm headed self tappers holding the top of the shroud to the radiator; remove those.   The shroud then lifts out of the bottom mounts where it sits on the radiator, up and onto the engine out of the way. Simples
    • Ok, disregard my “rate them” comment, sorry for my unrealistic input
×
×
  • Create New...