Jump to content
SAU Community

Recommended Posts

I've got everything except the turbine housing just waiting to be installed. They tell me late March for the housing but these days it's hard to predict delivery dates. 

I'm looking forward to the convenience and reliability of V-Bands on everything.

  • Like 3
  • 2 weeks later...
1 hour ago, r32-25t said:

I like the amount of room they give around the a/c line and etc, they were a nightmare with my 6boost 

That was my first thought also. 

I dropped coin on a frenchies kit, which is really awesome but be nice if the factory stuff all fit better with 6boost. 

Not sure how I feel about the compressor outlet being so close to the manifold though. 

Very keen to see one of these with a heat blanket over them. 

I'm going to get some mounts welded to mine to hold a rigid heat shield, I'm not fan of wraps or ceramic coatings. I hope the cast material welds ok, my fabricator reckons it will be fine but we'll see. 

Still an 8 week lead time on my turbine housing and no ETA on sequential box so I'm not in a rush.

Watched this yesterday, a lot of BIAS as they are now selling them but given how little info around I thought I would share. 

They claim 15% power increase ... yer I wish, love to see this comparison if anyone has seen it. 

 

So far the advantages over a 6 boober  seem to be :

Comes with a gate flange

Lighter - 5kg ish ? 

More compact - better AC and would help reduce heat transfer

Has a heat blanket option

Downsides :

Clearance of studs(6boober has this too) 

Higher cost

Reverse rotation turbos only( big issue for those that have a turbo) 

 

 

I really love it when people create smoothly distributed pulse-free gas inlets and outlets with no upstream or downstream geometry, no pressure fluctuations (which are actually waaaaay more than just fluctuations in a turbo manifold) on things like manifolds, then present a steady state solution instead of a transient solution. It's so sad.

And, to use the CFD that's built into Solidworks and present that as if it is any bloody good at all it even sadder.

  • Like 3
  • Haha 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
    • Thanks for the replies everyone. Definitely a coolant push. Oil catch can is empty and always has been. As the engine is out now I'll be having a good look over things. I do have some detonation on the piston tops from a trigger issue back about 5 years ago. I felt it and shut off then bought a new ecu and changed the trigger. Never been an issue since. It never hurt the power, its made almost 80hp more since that incident but I will pull the bearing caps to take a look. If the bearings are damaged I will do a bottom end refresh. Head is being re conditioned at the moment and the block will be cleaned and checked to ensure it's flat. I'll go with a kameari gasket and see how it ends up. The other thing I'm not super keen on is the cylinder colours. I suspect this is from the inlet manifold. The plan will be to put it back together, retune and then stick a plazmaman billet inlet on it and retune. I'm happy with the power, if it makes a little more, then great, but I would rather just make everything more efficient at this stage.
    • Maybe they'll look to do a bunch of presales to help inject some cash fast for their financial issues...
    • Does it also misfire equally when revving?   Josh is very correct in what you should do. The coilpack harness wiring loom itself is a known problem due to its age and the number of heat cycles it has gone through. Throwing parts at a vehicle to diagnose the issue isn't a smart or good way to do it. Secondly, you may have a bad coil pack, you pop replacements in, they fix that issue, but messing with the harness breaks it, so the issue persists. So now you think "well it wasn't the coil packs" and have to continue chasing your tail, potentially swapping back in your shit coil packs and returning the good ones (yes, I've seen people do this because 'it wasn't the problem' and they want to save money). And suddenly, you've got two issues with the same symptoms...   Diagnose, don't use the spare parts shotgun.
×
×
  • Create New...