Jump to content
SAU Community

Recommended Posts

That's nasty!

I think there is perhaps an inherent problem is using elastomers in such environments. The whole thing can and will get quite hot, and elastomers are not famous for their temperature resistance. On top of that, if the components are cast rubber or urethane and so on, there might be QA/QC problems with bubbles or voids in the material that could critically change their performance. They might just tear apart after being squished (presuming that any elastomers are used in compression rather than tension, I'm thinking that you squeeze one with a void in it and it tears the wall of the void to the outer edge of block, then the next time it extends or otherwise twists, it just gives up).

This is all purely hypothetical, but it makes me wonder if the things that they have put into it to make it nice to use/live with are perhaps going to cause occasional failures like this.

I wouldn't be getting up in arms over it, unless there are many repeats. I have personally ruined an Xtreme clutch - just an HD thing. I can't remember if it was still behind the 20 or was after the 25 went in. But it inverted some of the retaining spring/clip things around the outside. No-one could explain it. It wasn't thrashed, there wasn't heaps of torque being put through it, and there were no obvious problems other than the above. They were quite concerned by the event so they replaced it even though it was a few years old, which was very nice of them.

As far as I am concerned, these things happen with clutches.

  • 2 weeks later...
  • 3 weeks later...
  • 3 months later...

Group dedicated to people who have had failures and poor outcomes.  Good dozen posts so far. 

 

Probably the worst two examples 

image.thumb.png.c9067b758740bc7a9ae990375c83ae20.png

 

And this one apparently damaged a sequential and engine block(40k+ damage)

image.thumb.png.3da46a86f3a98f76cb2b35953d20ae10.png

  • Sad 1
On 27/08/2025 at 9:37 PM, MBS206 said:

Jim Berry

I'm getting PTSD flashbacks seeing that name again. 

With my turbo swift, I got 1,500km of street use on a Jim Berry clutch before it exploded and took out my input shaft with it. 

  • Sad 2
13 hours ago, niZmO_Man said:

That is horrid.

Reminds me of the time that R32 send the clutch through the bonnet, then the guy tried to sell his car using those pictures.

Are you thinking of Bens R32? I don't remember if his went through the bonnet itself, but it went through the chassis rail.

Brad (RISKIN) bought it, and turned it into a track car.

4 hours ago, Murray_Calavera said:

I'm getting PTSD flashbacks seeing that name again. 

With my turbo swift, I got 1,500km of street use on a Jim Berry clutch before it exploded and took out my input shaft with it. 

It's funny how anti people are of Jim Berry now. I remember when I pulled mine out (during an engine change) and inspected it and found it cracking badly. At that point in time so many people were even on SAU, were so pro Jim Berry, and that was after Bens GTR exploded his quite publically.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • That sounds like no chance of even importing one for road registering then Now I see why Duncan wants to check LHD rules for Targa...   I wonder how "bolt in" the AWD would be if you got one imported from the US and swapped it to an AUD one
    • Not to mention they drive like a bucket of bolts! yuck!
    • Ha ha ha, that's fair mate! We have the crackhead dogs now. Mainly because the missus wants the crazy dogs while she still has the energy and capacity to be able to keep up with them! Ha ha our current two are both Working GSD, there brothers and sisters (from the same litters) are in Police, Corrective Services, and I believe one did end up in defence force too. They're wild and fun, yet right now, both curled up asleep on the lounge room floor while we watch some TV. Mal is very likely the next dog (unless I get my couch potato guardian dog 😛 )   What are your Kitties names? Are you planning some house work, like those high kitty shelves, built in scratching post, and some cat passages from one room to another room?
    • Maine Coone, did look at but to big and fluffy As for performance dogs, we had Mals at work, performance dogs are fun to watch, but, way to much work for this old rooster
×
×
  • Create New...