Jump to content
SAU Community

Recommended Posts

10 hours ago, Duncan said:

not really....in that it is possible but it would be easier to pull the motor than to take the sump off in the car.  It's not just that the diff is attached because you remove the axles and driveshaft, but you have to remove the whole subframe to get it out which is a heap of work including brake calipers and steering rack disconnected, have to support the engine from above because the engine mounts to the subframe etc etc

Also, at that point if the engine support stand slips I hope you can bench press 200+kg of RB26. Considering the oil pan has to be RTVed on as well which has like a 15 minute working time between the first drop coming out of the tube to fully torqued to spec I would probably never attempt pulling the oil pan unless the engine is on a proper stand.

You also have to pull the box out to take the sump off an rb26 because a few of the bolts are inside the belhousing. 
 

just put something long and metal through the sump plug hole till it attaches to it and take it out through the hole 

the real lesson to learnt here for everyone is don’t use cheap parts because they end up costing more in the long run 

  • Like 1
1 hour ago, r32-25t said:

You also have to pull the box out to take the sump off an rb26 because a few of the bolts are inside the belhousing. 

That bit at least you can fit by drilling a couple of clearance holes in the sump webbing to get a socket in there

Update: I got the magnet out. I bought 3 different flexible magnetic reach tools, but none of them worked. The magnet on the tip was all less than 2lbs of force, so i had to buy a special cylindrical magnet that had a pull force of 9lbs. 

The magnet finally came in the mail yesterday, so i got under the car to get to work. The super strong magnet isn't that long, so i only have about 1 finger pinch lengths to hold it. I was so scared when i was going in the hole, that the 9lb magnet would just fly away inside the oil pan never to be seen again, but i had my butt cheeks clenched and finger gripped on that thing so tight, i managed to get it to suck the other magnet out. 

It was a victory for me last night. 

B888CDB2-0638-4558-81F6-17B81FF17A3B_4_5005_c.thumb.jpeg.e88d524e5a5d2b9fdcca9ba4e0f1b0f4.jpeg    ACA7CBEC-9CDD-4846-9A55-F5E90AD3F304_4_5005_c.thumb.jpeg.74037927ee3da46f0a6f76dc2abe2b67.jpeg   48FD0092-F352-478D-BA2B-4C4811CC3FE6_4_5005_c.thumb.jpeg.c92090812617ef23179a495162a77c42.jpeg

  • Like 6
7 hours ago, kevboost7 said:

Update: I got the magnet out. I bought 3 different flexible magnetic reach tools, but none of them worked. The magnet on the tip was all less than 2lbs of force, so i had to buy a special cylindrical magnet that had a pull force of 9lbs. 

The magnet finally came in the mail yesterday, so i got under the car to get to work. The super strong magnet isn't that long, so i only have about 1 finger pinch lengths to hold it. I was so scared when i was going in the hole, that the 9lb magnet would just fly away inside the oil pan never to be seen again, but i had my butt cheeks clenched and finger gripped on that thing so tight, i managed to get it to suck the other magnet out. 

It was a victory for me last night. 

B888CDB2-0638-4558-81F6-17B81FF17A3B_4_5005_c.thumb.jpeg.e88d524e5a5d2b9fdcca9ba4e0f1b0f4.jpeg    ACA7CBEC-9CDD-4846-9A55-F5E90AD3F304_4_5005_c.thumb.jpeg.74037927ee3da46f0a6f76dc2abe2b67.jpeg   48FD0092-F352-478D-BA2B-4C4811CC3FE6_4_5005_c.thumb.jpeg.c92090812617ef23179a495162a77c42.jpeg

I have to say, I was briefly considering getting a magnetic drain plug but never could be bothered out of laziness/cheapness and now I'm very glad I didn't.

  • Thanks 1
3 minutes ago, joshuaho96 said:

I have to say, I was briefly considering getting a magnetic drain plug but never could be bothered out of laziness/cheapness and now I'm very glad I didn't.

Magnetic drain plugs are fine. Just don't buy cheap shit ones. They're actually better than letting magnetic shit float around in your oil.

The magnet also didn't just "fall out". OP was drilling the plug out which allowed it to come out.

Even some OEM plugs are magnetic.

7 hours ago, MBS206 said:

Magnetic drain plugs are fine. Just don't buy cheap shit ones. They're actually better than letting magnetic shit float around in your oil.

The magnet also didn't just "fall out". OP was drilling the plug out which allowed it to come out.

Even some OEM plugs are magnetic.

I'm not doubting it does something, there's clearly a reason why Nissan bothered with it on the transmission/diff/transfer case but it's more just the effort of finding a drain plug that isn't going to have some unexpected design problem that makes me lazy. For example even the Nismo branded ones here spec way less than the factory 20 N-m. They say only torque to 10 N-m. That is getting absolutely trashed the moment you take it to any mechanic who isn't familiar with the specific requirements and assumes it should be torqued to factory spec.

  • Like 1
52 minutes ago, joshuaho96 said:

I'm not doubting it does something, there's clearly a reason why Nissan bothered with it on the transmission/diff/transfer case but it's more just the effort of finding a drain plug that isn't going to have some unexpected design problem that makes me lazy. For example even the Nismo branded ones here spec way less than the factory 20 N-m. They say only torque to 10 N-m. That is getting absolutely trashed the moment you take it to any mechanic who isn't familiar with the specific requirements and assumes it should be torqued to factory spec.

I thought you didn't let mechanics, especially those with no idea, work on your car any more? Wouldn't that mean it won't be an issue in your case?

45 minutes ago, MBS206 said:

I thought you didn't let mechanics, especially those with no idea, work on your car any more? Wouldn't that mean it won't be an issue in your case?

Sure, but why assume that will be the case forever? And why assume you'll be able to do an oil change to swap back to a stock drain bolt before that happens? And does it even matter when I change the oil at fairly short intervals? Life can be funny sometimes and unexpected things can happen. Like breaking a collarbone so you can't do any work on your car for a few months but the oil change is due so you have to take it to somewhere and hope they don't do something stupid like stacking the new drain plug washer on top of the old one.

  • Haha 1

Looking back, I’m pretty sure I over-torqued the magnetic drain plug because I was trying to fully crush the copper washer. In hindsight, I definitely should’ve used a torque wrench.

Either way, I ended up switching to a regular drain plug so I don’t have to deal with this kind of issue again.

Big thanks to everyone on the forum for your support—I actually talk about you guys to my friends and coworkers 

  • Like 1
8 hours ago, kevboost7 said:

Looking back, I’m pretty sure I over-torqued the magnetic drain plug because I was trying to fully crush the copper washer. In hindsight, I definitely should’ve used a torque wrench.

Either way, I ended up switching to a regular drain plug so I don’t have to deal with this kind of issue again.

Big thanks to everyone on the forum for your support—I actually talk about you guys to my friends and coworkers 

On the bright side, at least you knew that it happened and remedied before anything happened. A friend of mine just took his Fiat 124 to a shop for an oil change and they didn't tighten the oil filter housing properly. 4.5 quarts spewed out and even after refilling + tightening the cap the engine has a tick now.

9 hours ago, joshuaho96 said:

On the bright side, at least you knew that it happened and remedied before anything happened. A friend of mine just took his Fiat 124 to a shop for an oil change and they didn't tighten the oil filter housing properly. 4.5 quarts spewed out and even after refilling + tightening the cap the engine has a tick now.

Your friend:

well-someone-messed-up-v0-rwkaynhp8paa1.thumb.webp.44cebc43a7f9e36c5b7795509d05bd8b.webp

Not my proudest moment, but about 6 years ago, i did an oil change on my ex-gf's car while drunk. It was a Toyota Rav4 so they had a weird oil filter holder device that's not the standard oil filter. I went to start up the car and drove it from the driveway to the parking spot and i turned around to see the biggest oil spill i ever seen. It didn't end up being a problem because i filled the oil back up and tightened the filter properly, but after that experience i never worked on my cars drunk. 

  • Haha 3

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...