Jump to content
SAU Community

Recommended Posts

White C34 on Castlereagh Rd near Cranebrook Rd Penrith NSW going towards Richmond this morning around 8:50am. I was going the other way, waved but no response from male driver. His female passenger must have been a honey to ignore a fellow stage-ian. :rolleyes:

Spotted a silver Stagea (think the last numbers on his plate were AAY) near Bridge Road (Adelaide) yesterday, waved and tried to catch him but he was too quick lol, i've seen him a few times now, next time you see a short girl behind the wheel of a white 25T RS4 you could always wave back :whistling:

Spotted a silver Stagea (think the last numbers on his plate were AAY) near Bridge Road (Adelaide) yesterday, waved and tried to catch him but he was too quick lol, i've seen him a few times now, next time you see a short girl behind the wheel of a white 25T RS4 you could always wave back :whistling:

Here's a (hopefully non sleazy) wave from QLD ! :action-smiley-069: Female Stagea owner, that's awesome. Big up.

:action-smiley-069: hello right back at ya! i dont know many girls that actually like performance cars...sad really lol. I even had to get my stagea seat rails moved forward 2 inches so i could get my clutch in all the way :whistling:

:action-smiley-069: hello right back at ya! i dont know many girls that actually like performance cars...sad really lol. I even had to get my stagea seat rails moved forward 2 inches so i could get my clutch in all the way :whistling:

It is sad ! Last time I found a girl that liked performance cars, I married her ! She's a small one too. No wonder she likes Holden Gemini's.

I'm 6'4", and honeslty could do with the seat rails 1" - 2" further back. Rear seat passengers would have to be amputated from the knee down though :)

If you feel like it, put up some pics of your Stagea in here http://www.skylinesa.../page__st__1780

Cya :)

QLD - Spotted a stock white S2 going south on highway near Tallebudgera @ around 4:30pm today. I :action-smiley-069: but got deeee-nied.

on Cowarra st taren point i saw a Silver PNM35 at a fiberglass place and then while i was watching it a White C34 drove past then of course there was my Black m35, i personally have never seen more stags in one place at one time.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
×
×
  • Create New...