Jump to content
SAU Community

Recommended Posts

Congrats. Not bad at all. Bet your itching to break into the 11's now.

Shouldn't be too hard, just need a cool night and some more boost. :)

Unfortunately my map sensor is out of resolution, need a 4 bar map and a retune.

I think I got it down under 2 seconds, wasn't too interested this time due to the heat, couldn't push the car like I wanted to. I will get some videos next meet, heading back up soon after the retune.

It was funny feeling the back end step out on launch, I have never been able to launch on boost like that before. Loving this new turbo.

  • Like 3

I think I got it down under 2 seconds, wasn't too interested this time due to the heat, couldn't push the car like I wanted to. I will get some videos next meet, heading back up soon after the retune.

It was funny feeling the back end step out on launch, I have never been able to launch on boost like that before. Loving this new turbo.

Good to hear. Looking forward to vids and 11 sec pass.
  • Like 1
  • 2 weeks later...
  • 3 weeks later...

The birthday present my wife ordered for me arrived and I spotted this !

It's quite nicely done on an aluminium sheet, and all the lines are embossed (not sure if that's correct lol) but you can feel the spokes on the wheels for example.

post-58831-0-25454600-1453118063_thumb.jpg

  • 2 weeks later...
  • 4 weeks later...

Spotted the Devils creation at Robertson pie shop ( Mac Pass ) on Sunday, lets call it a RS450?

Anyhow C34 V8 Turbo Manual 4WD with R34 front end ( F**KN Baller ) :woot: luved it, great job done on conversion & owner very approachable to discuss said car.

Hope to see it again soon to drool some more, well done sir, well done. :worship:

Good to see high quality cars sneaking around sleeper style. :ninja:

Regards Jase. :cheers:

Spotted the Devils creation at Robertson pie shop ( Mac Pass ) on Sunday, lets call it a RS450?

Anyhow C34 V8 Turbo Manual 4WD with R34 front end ( F**KN Baller ) :woot: luved it, great job done on conversion & owner very approachable to discuss said car.

Hope to see it again soon to drool some more, well done sir, well done. :worship:

Good to see high quality cars sneaking around sleeper style. :ninja:

Regards Jase. :cheers:

LOL, Jase, you need to check this out: https://www.youtube.com/playlist?list=PLvKTvFJhZUJi_4_zliMEucYtH7R6D_mjD

Long time no see buddy, hope you are well.

Terrible photo, but spotted Leanback on my way home.



12527695_10153630544907946_1717541288_n.

Was in the racecar, but said hi anyways. Probs looked a bit odd a guy in a honda going I own one but I do I swear.

Edited by BIGZED
  • 3 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...