Jump to content
SAU Community

Recommended Posts

Skyline model = R32 GTST

Wheel diameter = 17"

Wheel width = 8" front 9" Rear

Wheel offset = +42 Front +42 Rear

Tyre size = 235/45/17 Front 235/45/17 Rear

Modifications to fit: front requires 5mm spacers to give enough spacing with 235's

Hi guys,

I'd like to know if I wanna get rims for my R32 gts-t in 17 inch with 8" front and 9" rear So, what offset should I get to make the rims sit right to the outside of the guard without rubbing? (will lowerring the car too)

any pics would be good

Cheers

Ford

Quick Question Guys.

I have been reading over this thread and it appears that the largest wheel size you can put on an R33 GTR with NO modifications are: 18 X 10 +18 or +20

I just want to confirm that you dont have any clearance issues as far as with turning or anything like that. 10" wide wheels would be perfect for my build as I need to help with traction, but I just want to make sure that I am not going to have any problems turning or anything along those lines as I will probably be getting into doing road racing as well.

Thanks a lot for the info and the help guys. I do greatly apprecaite it,

-Sayajin

  • 2 weeks later...

Skyline model = R32 GTST

Wheel diameter = 18"

Wheel width = 8.5" front 9.5" Rear

Wheel offset = +37

Tyre size = 225/45r18

Wheel type = Work meister s1

Modifications to fit = i have coil overs and no inner guards

Will these fit?????????

Skyline model = R33 GTST

wheel type= advan racing series 1 tri spoke

Wheel diameter = 17"

Wheel width = 8" front 9" Rear

Wheel offset = +35 Front +35 Rear

Tyre size = 235/45/17 Front 235/45/17 Rear

Modifications to fit: none

i was looking at getting some 18s for the line but im not shore what offsets to go any help would be great im looking at 18x8.5 front and rear with tyres probly 235x40x18. car has been lowered nuthing stupid tho and still has standard brake calipers etc i would like to have the offsets so that the wheels are close to the edge of the gaurd cos it looks funny when wheels sit inside the gaurds heaps so any one who can tell me wat offsets to run would be great

  • 2 weeks later...

Skyline model = R32 GTST

wheel type= work VS KF

Wheel diameter = 18''

Wheel width = 8'' 9''

Wheel offset = +34 front, +38 rear

Tyre size =235/40/18 front, 265/40/18 rear

Modifications to fit = none to stock height (till i lower it, then it will be rolled & flaired)

Ok, teh beast is an R32 GTS4.

Front wheels: 18 x8, offset 29mm.

Rear wheels: 18x9, offest 35 mm.

Tyres F & R: 235/40/18.

No mods to fit. However, once the car is lowered and a camber correction kit fitted the rear guards will need lipping.

Could be run lowered with excessive camber ( was when I bought it ) but that's dumb anyway.

@ subie: You'll be f**ked on the rears, mate. Guards will need lipping at least, judging by my car.

Dunno about the fronts but don't like your chances. I intend to change to 18 x 8 all round.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...