Dose Pipe Sutututu

Harros, My entire rear boot and rear boot spoiler is for sale. Much hectics for your R33 S1 or S1.5. Paint is good, however car has been washed twice in over four years so there's a layer of grim on it. More Photos here: https://www.facebook.com/traklifeofficial/photos_stream Colour is some hektic Autosalon Final Battle Dark Blue/Purple Colour.. Price: $199.99 Location: Canley Vale, NSW

most likely this one: http://www.plxdevices.com/PLX-Wideband-O2-Air-Fuel-Ratio-Sensor-Modules-Gauges-s/125.htm

needs calibration. AEM UEGO no need, and has serial out for ECUs. PLX, etc... new AEM failsafe no serial out (rage)

however both Mafia and I aren't killing them through sensor positioning.. they're killing themselves... it's a known fact Innovate likes munching sensors.

make sure you buy double hex socket set and 3/8" long sockets.. 1/2" won't fit and 1/4" you'll snap them. (yes I learnt the hard way)... ARP studs comes with a sachet of assembly lube, more than enough for all the studs/nuts.

fuuuuuarkkkkkkkkkkkkkkkkkkkkkkkkkk set to 5/5 and brapppppp LOL

^ fuuuuarkkkkkkk strong dose, dat 6+6 blade compressor = more dose.

much jellies.. your boat sah clean!!! I've own mine for 4 years, has been properly washed twice LOL. Usually gets a hosing or a $2 job at Car Lovers.

Pedders = BC BR = Blitz ZZR They're identical... however not sure if the valving is identical. Have been in both BC BR and Pedder equipped cars and both felt harsh considering both were your run of the mill 8/6kg flavours. MCA even advise me to get softer, but I ended up with 10/7kg but I like it very much the way it is. I've dropped both ARBs to the softest setting and utilise the stiffer springs to reduce the roll. Car feels very compliant on the track and when the dampers are clicked back for the drive back home they're honestly just as comfortable as my old Bilstein shock/spring combo (of course hitting a pot hole or running over reflectors aren't as comfortable but you get the idea).

MTX-L is hit and miss, my current gauge is going strong however the same one I installed not long ago is cactus

It's not the heat that kills the sensors with the Innovate kits, it's the gauge itself that cooks the sensor.

yeah easy man! yes they recommend adjusting the spring seat to adjust the height of the car.. I believe they recommend this to 1. pre load the shock so you're not always at the top of the shock stroke and 2. you won't bottom out the car.. the car would essentially hit the bump stops instead of the ground. so the free play experienced when the car is lifted is quite normal. Japanese and decent Bilstein, KW, etc.. all have helper springs to avoid the free play/spring drupe.

Back again, 372kW @ 1.75bar (1.8bar spiked a little)... motor has not popped and even went to a track day on the 30th of May. Motor did push some coolant, I believe the OEM head gasket isn't too happy.. even with ARP studs.. might go and torque them up some more LOL. Details: http://www.sau.com.au/forums/topic/55845-rb25-turbo-upgrade-all-dyno-results/page-54#entry7731169

sensor death or gauge death?

Pintle cap, eBay them cheap as chips Only the top area snapped so it will be fine, the seals won't fall through so don't be too worried. I personally wouldn't change them

Need displacement

the mid muffler is a basic hurricane round 3.5" muffler, the resonator has been cut off same cat back (HKS Priest) and the sides trimmed till the pipe work became 3.5" the rear muffler is a massive HKS Priest muffler which isn't really 3.5" more like 3.25" but good enough. Funny enough, when the gate cracks the exhaust gets even quieter.. (it's plumbed back after the cat) like so (old pic, all the shit is wrapped up and also the wiring has been cleaned up):

Once you get 2x mufflers & a resonator to remove the "bark" from the exhaust it's pretty quiet.... the tyre/road noise is the loudest thing in my car at cruise. On the loud pedal there's "some" noise but you can still hold a full conversation without raising your voice.

FWIW.. NPC actually uses Exedy parts Exedy Pink = gay Exedy Silver = good NPC (Which is just Exedy) = bettererererer

Yep I run a 3.5" system and I can tell you it's quieter than 90% of the skylines out there.... 3.5" dump -> 3.5" cat -> 3.5" mid muffler -> 3.5" resonator -> 3.5" muffler

Needs more boost man!

Didn't I say head studs a page ago?

Are you on E85 or 98RON? E85 doesn't "really" knock

ARP studs are cheap Changing studs (without removing the head OR cams) is also a cheap/easy process... Just change studs and add in as much boost as possible, i.e. still no more power can be made #e85lifey0