Jump to content
SAU Community

Duncan

Admin
  • Posts

    33,524
  • Joined

  • Last visited

  • Days Won

    212
  • Feedback

    100%

Everything posted by Duncan

  1. lol the funny thing is, someone went to the trouble of putting it on and tensioning it. Perhaps it did actually work (a little, at first) You just need the right belt and that will be sorted, the globes, yes just buy some D2Rs (more recent ones are compatible so no issue there) Re the clunk....best to get a mechanic to look at it. There are about a million (OK, 10) places between the transmission and the tyre that could clunk, no point just guess it is a tailshaft.
  2. I used to run 265/35/18 on 18x10 0n my gtst, but I don't know what offset they were, and I bet people have fit bigger back there....
  3. I've not noticed a practical difference, and I've been using OEM in one car and poly in another for years. I went poly when I replaced them due to price and availability not concerns about durability or life.
  4. Fair enough and thanks for saying. My experience is with Stagea W34 not Skyline R34. They run fine with manual computers and auto trans but it sounds like there are differences in later model/R34. Also, this suggests the Stagea ECU he has will not do the job with the later R34 auto trans for the same reason.
  5. Nistune in the new ECU will resolve my point 3 above, but it won't correct any physical wiring differences. On the other hand, if you can nistune your original ECU than both 1 and 3 are covered off.
  6. Wiring sounds exactly right to me. Right size cable, right size relay (larger than needed), right size fuse (smaller than cable max), right order of wiring. I'd replace the pump next, not the wiring (unless it is damaged again), I think it is drawing way too many amps. Before you do one possible test is to check the amps being drawn by the pump (you put the multimeter in line with the positive or negative) but check the multimeter can support up to 20amps, I think a lot are limited to 10.
  7. So, in summary, there is a fair bit more work before this will run OK. Whoever gave you the idea that you could bolt on the turbo, injectors and ECU and it would run skipped a few steps. 1. One way or another you need to match the ECU wiring to the ECU. You need the pin outs for both ECUs (old and new) and compare every difference. You either need to cut and rejoin your current loom at the ECU to match the new pins, or you need the ECU loom that matches your ECU, and then change a few of it's connections at the other end where they are different (and they will be). You may need help from someone who has done this before if that doesn't make sense 2. There are at least a few mechanical/electrical differences to deal with. I'm not familiar with this particular swap but the guys mentioned the boost sensor, I would expect there is also a difference with fuel pressure regulator needing to be a turbo version and have a boost input, some sort of boost controller, fuel pump is probably different, air flow meter might be different as well? 3. The ECU you have may still not run the DE engine well due to differences in cam, VCT and compression. You will probably need a nistune at a minimum to get in running well. Since it is a manual ECU it won't talk to the auto; it will work but it won't give smooth shifts because the trans can't tell the engine it is changing gears and to reduce power (timing) momentarily There is still a big job ahead to get it running properly, you've gone down a difficult path. Realistically you need to find some other way to get to work for a few weeks...
  8. according to engineering toolbox (I'm sure there are other sources too) 8WG over 6m length can carry max 25amp at 12v.https://www.engineeringtoolbox.com/amps-wire-gauge-d_730.html According to DW, the pump draws up to 18amps so it is close but should not be close enough to cause trouble. https://www.deatschwerks.com/sites/www.deatschwerks.com/files/DATA/DW300 Tech Sheet.pdf What is the route and distance from the battery to the pump for the +, and what size fuse is in it? And where in that run did the cable melt? And what is the route for - as well?
  9. You don't want to rebuild it because you are spending $1,400 on timing belt etc. Cheap and dirty will cost $5k, basic rebuild $10k and of course the sky is the limit depending on what you want to change. Rebuild means labour for engine in and out, then disassembly, cleaning, measuring, new gaskets, head and rod bolts. Machining, Measuring, rings and bearings. Yes you can save on that, particularly if you can do most of the labour, and you can decide how much you want to reuse, but it will still be 3-10x what you are already spending. BTW are you sure the oil leak is from the head/block and not the cam seals? It is much more common there. If you really wanted to deal with that, head off while the timing belt is off is an option, but it sounds like that may have been done before, and obviously not 100% successfully if it is leaking there (suggests head or block may not be flat...) BTW, if you are doing timing belt, always change the idler and tensioner stud/bolt, and consider doing the water pump, cam and oil pump seals while you are there.
  10. And...if it's always done it, it may well be a problem with the pump, not your wiring.
  11. Would need pics of exactly where it is starting to slide out. Normally if the wiper blades are in the right way up there is a little catch at the end of the blade that holds into the wiper arm
  12. still need a little more information. how much accelerator (100%?), and for how long? Is it initially OK when you floor the throttle? Does it start to pop or hesitate, and if so at what revs?
  13. Oh, and definitely not normal. The oil and smoke systems inside RBs are sealed, they should never come out.
  14. Almost certainly a cam seal leak. There are head oil returns near there but the head gasket seals them
  15. Love it (both the colour, and that it was your third ) They also came in a very light green and a two tone light green....but that is the green I meant. And I know I sound indecisive, but I also love that series 2 yellow. It is so understated for a family car, kind of gives away the stagea secret....
  16. yep understood, there is a lot of good wiring info in that doc including ECU pinout (slightly different to 32/33) and MFD wiring which was very helpful. No idea what it's source was because generally english manuals are only available if the car was officially sold in an english speaking country like the R32 in Aus. Anyway, yes, the exploded diagrams, procedures and torque specs from the r32 manual will be fine for r34 assembly
  17. interesting conversion. probably goes way better than my td42 one but I suspect an rb25 will still struggle moving all that weight. surely it is 4wd....if the original engine was td28 it is likely all the original patrol 4wd stuff bolted right up.
  18. Depending on what exactly you need to do, engine wise the 32gtr manual will be fine. mechanically they are same/same, and the electrical differences are minor.
  19. I was going to say that WD9E-R34AJ0 is not a valid part number, but hey when I googled it I found this: https://netred.se/fakethinkpad/documents/R34_servicesupplement_OCR.pdf
  20. That's what I assumed too There is an awesome green, manual stagea in sydney that would probably be for sale soon. Well looked after, low klm car in good condition.
  21. sure....if you're in no rush and willing to take the risk that internet advice has no value....post em up I don't know about the rb25 intake manifold gaskets, and in any case there is an upper and lower half so pics may be required. AAV will have a gasket and matching mating surface on the manifold. If the gasket is in good condition (ie flat an unbroken), just re-use it. Otherwise hit kudos or similar to buy one but you will need to remove the old gasket and clean both surfaces well (brake cleaner, razor blade or even scotch brite pad manually or on a air or power tool). New gasket here: http://www.kudosmotorsports.com/catalog/valve-gasket-suit-nissan-skyline-gts25-gts25-rb25de-rb25det-p-1200.html Rocker cover gaskets can be reused if they still have a bit of flexibility. If they are cracked on super hard replace. http://www.kudosmotorsports.com/catalog/camshaft-cover-seal-suit-nissan-skyline-gts25-gts25-gts25-p-207.html . Some people use a VERY thin bead of silicone in rocker covers but if the gaskets are OK and covers are bolted down properly they won't leak. You do need to use silicone on the half moon seals at the rear of the cam, and those half moon seals are more likely to need replacement as they can rip when you remove them.
  22. The only way that will work is to get someone to help out at your place for a few days, since you won't be able to collect everything that came off, and it is a disaster job for a workshop.... There must be someone with some experience in Sydney who needs a day or 2 overtime on the weekend....
  23. m10x1.5 x about 40mm long on a GTR, I bet they are the same since they bolt into the gearbox
  24. slippers very appropriate for this time of year. sure sounds like you have an air leak, and probably in the booster itself. In the engine bay there is an air line from the rear of the plenum, through a 1 way valve, into a cannister and then into the brake booster. Check each of those lines for splits and make sure the 1 way valve is working (ie, you can blow air through from the engine side, but not the cannister side). But I think most likely the booster has a leak. You can replace with second hand or reconditioned one.
×
×
  • Create New...