Jump to content
SAU Community

Recommended Posts

Rather than obviously starting a new thread here is my plan.

I plan to be running about 17 - 20 psi with a flow rate of about 500hp(imagine a 3076r). Would the turbo blow out the spark from the standard coil packs?

I plan to buy all the gear I need when I fit the turbo in so I don't want to install it then have something break then have to buy something else.

Someone tell me what I should get. I'm looking at yellow jacket coils, Ive heard good things and they are cheap compared to others out there. Now the plug. People say run a smaller gap when at higher boost but if you run bigger coils run the bigger gap. I'm planning ahead for all this and need my gear ready. Should I go out and buy my self a set of 1.1mm? Anyone suggest which spark plugs I should get? I'm not too keen on changing plugs every 5000km.

I'm estimating about 280 - 300rwkw.

You'll probably need to go aftermarket, they're only about $400 and running that boost will be pushing 15 yo coil packs. Yellow jackets are seemingly as good as splitfires (they've been round a while now and still going strong), with 2 years warrenty and for 2/3's the price.

Changing spark plugs every 5-10k km is something that you'll probably have to live with, esp running on much boost. Plenty of people like that at least changing that regularly they are monitoring cylinder conditions that regularly too, gives you a heads up if one plug is fowling too often.

You'll probably have to go 0.8mm gap for that boost, it seems to be what most people do. I'm not sure if that'd be a 7 or 8 heat range, but for 7 i'd go with bcpr7es/bkr7es or fr8dp (bosch plats for cheap)

If you want any more info for this power range look at the dyno thread.

Alright well I'm getting a set of yellow jackets. After re reading the thread alot of people here are using a 1.1 gap when running better coils. Should I do the same or should I jump to 0.8?

I don't really feel like buying plugs, fitting them to see they work like dick then buying another set again.

Ill be sticking with a 7 heat range as 6 I recall being stock and the cooler ones respond better with more power. Gonna buy my self a bulk lot of copper plugs and change them every second time I do an oil change or when I notice pops and misfires.

Also what do people do when monitoring their cylinder conditions? Do you mean conducting a pressure test every time you change the spark plugs? Pretty sure you'll be ending the life of the cat converter pretty quickly.

To sum up all my shit,

What plugs should I get? 300rwkw 18psi rb25det with yellow jackets?

Its always best to run the biggest spark gap possible. Try 1.1mm bkr7es11. The reason we run a colder plug with higher powered engines is for safety. More power means more heat and if the combustion temps start to make the spark plus glow ( which happens) than the glowing plug can ignite the fuel/air mixture before the spark plug is ready to fire. This is called pre ignition. Which will kill ur motor within seconds.

Imagine the piston trying to travel up the bore and the flame burning above it trying to push it back down. = not good

Also what do people do when monitoring their cylinder conditions?

To monitor cylinder conditions u need to read the spark plugs condition.

Yep, the condition of the spark plugs can tell you a lot about how the engine is running. ie if they're a little covered in soot that's normal, if they look like they've been damaged by heat, or they're covered in a thick layer of unburned fuel (soot) then you're getting a warning before things go wrong.

Splitfires are more widely used because they've been around longer than yellow jackets. It's probably true that there have been more problems with yellow jackets, but the people with yellow jacket problems just get sent a new coil/coils under warranty. If you want confirmation of who's using what making your power, just look at the dyno thread.

  • 1 month later...

For what it's worth to whoever; I had a misfire issue which would start from ~4000rpm and cause issues anywhere from here on up, which is where the car starts to make decent boost.

Car has splitfires & new coil pack wiring harness - runs Vipec management and makes 500rwhp.

It was running BCPR6ES-11 (ie 1.1mm)... put a new set of the same plugs in. No help.

Pulled the 'new' plugs and gapped to 0.8... changed misfire from big bangs and cracks under load to short fast pops.

Had pondered and checked up on a lot of things, swapped igniters with a mate, was going to swap CAS, splitfires, loom, etc

Today threw in a set of BCPR7ES plugs, gapped to 0.8... misfire instantly gone. Pulls hard from 4500-8500rpm in all gears, well... maybe not 8500 in 5th hahah but you get the idea.

Happy as f**k now... back to dishing out bulk chop :)

Hopefully that can help someone too.

  • 2 weeks later...
  • 1 month later...

ok, firstly, i know this is in the forced induction thread but im getting no replies in the N/a one D:

Im looking at a, well over due, new set of plugs my 32 N/a

anyone bought off ebay ?? alot cheaper and was lookin at getting a set of these

http://www.ebay.com....23048a3aa1#shId

any feedback on them ?

cheers

  • 2 weeks later...

Been running BCPR6ES .8mm gap in a RB25 neo pushing 247rwkw for around 6 months.

been getting an occasional missfire in high revs (1st & 2nd gear) so not sure if its plug related, but i'll be switching to BCRP7ES .8mm as recommended by a few ppl in here so hopefully fixes the problem.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
    • So, now all you need to do is connect the 2 or 3x 12v feeds into the unit to permanent 12v, ACC 12V and IGN 12V that you can find in the spot behind the stereo, and the earth, and then it will switch on with the car.
×
×
  • Create New...