Jump to content
SAU Community

Recommended Posts

This is how Gibson managed the blowby. I assume due to the small size of catch can, and the amount of boost they ran, they had it well sorted.

I would say the drained chamber over the rocker cover would be stuffed with steel wool or baffled. Not sure if the catch can is drained back to the sump, but it seems to have a breather to the sump.

post-63525-0-25680000-1417096802_thumb.jpg

less thinking more doing shit that works

in the getto

Dash ten on pasengers side
image_zps1ceccf15.jpg
Two dash 12 on the drivers side, angles and spaced so as not to hit shit and be able to tighten the f**ker up

note that they are above the windage/baffel
image_zps6bfcbf80.jpg
Baffled and shit

door hinges from bunnings
image_zps52ed1d07.jpg[/url

ml]shep7_zps01a2f7a8.jpg

dash 20 atmo vent (strait to the ground so people behind me can EADC)

getto as f**k but works a treat

  • Like 4

I've bought a rubber flappy thing that tomei makes, its their universal jobby.

On a 25 sump the passenger side doesn't allow for a vent abovethe windage tray, should I just cut it out and mount the tray lower down to allow for that?

The Gibson engine was dry sumped and scavenged from multiple points

No they weren't, grpA rules stated it had to be wet sump.

The photo of the Gibson engine bag shows only the separator, the other part of the catch can is where the battery in the R32 normally is.

This is how Gibson managed the blowby. I assume due to the small size of catch can, and the amount of boost they ran, they had it well sorted.

I would say the drained chamber over the rocker cover would be stuffed with steel wool or baffled. Not sure if the catch can is drained back to the sump, but it seems to have a breather to the sump.

9572626787_019bd1895c_z.jpg

9575419288_e3446a4643_z.jpg

9575423336_3ca4c10bb6_z.jpg

  • 3 months later...

Ok for years this even to this day has been a problem for me. Now im only on page 5 of this thread and intend on reading it all anyways. But I have a few points that I know about from reading here and on other nissan sites. The oil pump collar problem ive personally gotten over. The oil blowing out not so much. All my 25 suffer from this. I feel its the additional rpms I run like 8500rpms. And now im learning that these rb motors were ment for only 6k. Like what the hell. :angry:

Ok so ive done like 3 things out the list

1. I did the head drain

2. I did the restrictor in the block but now learning I shouldn't run 2 of them but should have blocked one out. (To late) dont mind pulling the head.

3. I did the collar.

FYI.All my 25's run N1 oil pumps.

Thats it. I have always looked at the head. The oil returns by the head bolts is what you gays are saying to drill out bigger and the same to the block.?? They seem big enough as is, as part of the washer covers a part of the hole already and if made bigger then what will the bolt/stud pull on? next is at the very back of the head there is 2 major oil drain its in the photo ill attach. What do I do to these. Just hone them out as big as I can go. ??

Last can some post photo if not already in the thread again please, as im only on page 5 at 15 pages a day is my goal:D

Now all of this said. Just a estimate here can an rb motor now do 10k all day with other issues and dont blow oil out. ????? This issue needs to be addressed.

With my rb26 build I regret now not doing the machining of the oil return ports I am running an oil accumulator and a racefab 9.5L sump cooler and a tomie oil pump 1.1 oil restrictor size.

Im so frustrated :wacko:at this. As im running a tomie oil pump as well,

And I will be spinning this motor at about 9k or more cause I dont care for it especially now. Well ill continue reading bye

That's why I suggested reading just the last 15 pages. Ideas have developed since that thread was started and oil drains at the back of the head are generally agreed to be a waste of time and proper sump venting to a catch can the way to go.

BTW RB26 and even RB30s can be made to spin to 10,000 rpm if you do it right.

Im at page 16. Well im not having this problem with my 26 as yet. But all my 25 are doing this. Ill read the last 15 pages then. I still want to read the whole thing though. Heres an idea. Just an idea though. See that other are open to menstion ideas. From the back of the head drain cant some kind of pump be added and controlled to come one at a predetermined rpm point. Using a rpm trigger switch. This pump will be inline and pump the extra oil from the head to the sump. Just an idea.

Edited by MJTru

I track my built 26 regularly and always used to fill the catch can cos I'd rev the shit out of it.

Now I've learnt to keep it below 8K rpm and can do a whole day with out touching the can.

Motor is pretty basic, standard sump with Tomei baffle, N1 pump, oil restrictor & enlarged oil returns. Just wish I had of known about putting a sump breather in years ago when it was built.

I don't actually have a breather, I meant I wish I had one fitted. If you flick a couple of pages back on this thread there should be some images of peoples set-ups hence the reason for Bob recommending to read the last 15 pages.

I am as we speak. Just to work but im am reading it as time permits. What funny is someone mentioned venting the sump would let the oil drain easier. This I read in the first 16 pages. But at that time peopel weren't jumping on board. I will go back and reread that. So venting the sump will work. Hmmmm??? if this is the case I have to mod my setup. See I only have one oil return on my racefab sump and that goes to the rear head oil return. The front turbo drain is for the single gtx3582r. I can pull the sump out to do that so im thinking ill move the head drain to the second spot that was used for the rear turbo when it was stock. Then vent the sump.

What you guys feel about that. I drag racing this car and intend on spinning the motor to 9k on some days.

Edited by MJTru

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • 310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
×
×
  • Create New...