Jump to content
SAU Community

Recommended Posts

personally i would like to shake rick kellys hand .anyone who punts lowndes of the track at anytime is my hero

That sort of low brow, rock ape attitude is symptomatic of what is wrong with the current touring car formula where aspiration & excellence are exchanged for monosyllabic grunting to the effect that red is good & blue is bad, or vice versa.

  • Replies 227
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Just been confirmed that the Kelly gang have been awarded this years championship....

So that will confirm everyones tactics for next year. Stooge around in 20th place at every race meeting & punt off anyone who gets ahead of you in the points.

What a disgraceful piece of work.

Edited by djr81
So that will confirm everyones tactics for next year. Stooge around in 20th place at every race meeting & punt off anyone who gets ahead of you in the points.

Nope, they have already announced a change in next year's points per race. So that it makes it worthwhile to actually RACE for a higher place, now there's a novel idea.

V8 SuperCars is all about managing its image, and it doesn't look good when someone wins the championship after only winning one race. Especially after 2005's Accumulator result.

:laugh: cheers :huh:

Rick didn't even win a round,

Here is the breakdown:

R.Kelly C.Lowndes

1x 0 4

2x 4 0

3x 3 3

4x 2 2

5x 0 0

6x 1 0

7x 2 0

8x 0 0

9x 0 1

10+x 1 3

I hate the little fag just as much as anyone, BUT it just goes to show MONEY really does get you somewhere.......... a consistant car! we wouldn't want them to race all year and then have 1 round as a nationals, cos then the likes of Paul fat head Morris could hava chance! :laugh: Still can't get over that fat shit used to have Air Con in his car!

now roll on with chanel 7's coverage i am old enough to remember they were a lot better than what 10's coverage was at least 7 showed the support races as well so you had a full days racing not 2 hours of v8's and 2 hours of ads

That sort of low brow, rock ape attitude is symptomatic of what is wrong with the current touring car formula where aspiration & excellence are exchanged for monosyllabic grunting to the effect that red is good & blue is bad, or vice versa.

hehehhee your funny i like you .

gee craig even looks like a rock ape how he ever learned to walk without scraping is knuckles on the ground astounds me .

your boy isint squeky clean either and is quite happy to use the front bumper to push people along to get them out of his way seen it many times over the yrs.

if i can start up the front its not a prob but if he has to start near the back he can push and shove with the best of them this time he screwed up the cnr b4 did not want to concede a place and stuffed up end of story

now roll on with chanel 7's coverage i am old enough to remember they were a lot better than what 10's coverage was at least 7 showed the support races as well so you had a full days racing not 2 hours of v8's and 2 hours of ads

Is that because NOBODY showed any support races?, and if they do now, does that mean they will have to get permission from SBS to show them as they have the rights with Speedweek?

Long time between drinks for Channel 7, hope it does work out for them! As i and many people want to see decent coverage!

Whats the bet channel 7 wont show support categories either. And dont forget back when Channel 7 had the rights there was only one race per round, nto the case anymore.

And Moffat and Raymond? No thanks, with the exception of Diffey i like the Channel 10 guys.

Silly thing is he admits he was only shooting for top 5 finishes. Hell he didnt even say podiums, or race wins but wasnt going to do anything silly to get ont he podium as surrendering a top 5 result would hurt his chances.

He flat out came out and said he wanted points for the championships.

Thats like me saying i dont want to bunt a nice attractive girl, i just want to go out and bang any grizzly chick because i need to keep the yearly average up, or at least do better then last year.

..er well maybe not :laugh:

a also remember when channel 7 had the car racing....

got to see two whole races a year!!!!!

Soundown and Bathurst.....

At least with channel ten we got every round..... Hopefully channel 7 will not drop the ball.....

also, Rick Kelly DOES NOT!!!! deserve the title....... But you get that!!!!!

Niether did Shcuey, but nothing changed that either.....

Thats like me saying i dont want to bunt a nice attractive girl, i just want to go out and bang any grizzly chick because i need to keep the yearly average up, or at least do better then last year.
I guess i'll just follow you around and take all the attractive girls that you knock back...
now roll on with chanel 7's coverage i am old enough to remember they were a lot better than what 10's coverage was at least 7 showed the support races as well so you had a full days racing not 2 hours of v8's and 2 hours of ads

If rumors are correct 7 won't be showing any support races and maybe not all the v8 races :happy:

Not to fan any fires but i found this

http://cgi.ebay.com.au/RICK-KELLY-VZ-HOLDE...1QQcmdZViewItem

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...