Jump to content
SAU Community

Recommended Posts

HAHAHA ok so my mate got done for his car being to loud,

so we went and got heaps of Fly Wire and down the road from the place we pulled over and

you just scrunch it up and shove it in the exust pipe!

dont drive a long distance with them as they burn out,

when it was finished being tested ( IT WORKED!! )

we just gave it heaps down the freeway and the flywire shot out the back!

it was really funny, people wore driving past us,

and i was shoving flywire up an exust!

haha

it did work though!

Ho hum.

So... Registering things in the land of VIC.

The car was previously registered by its prior owner in VIC, however whilst it "passed" a roadworthy cert in VIC (i got one done by the previous owner), when i brought it to ACT i had a bunch of problems - since rectified.

However rules aren't the same place to place.

When I hit ACT i ended up getting it engineered with the following to get it passed (as well as having it retinted).

Non-standard Rims/Tyres, 18x8.5, 18x9.5 rears

Non-standard Fuel Delivery System (Fuel Pump etc)

Non-Standard Exhaust

Electronic Boost controller

FMIC

Non-standard Coilovers

Body Kit

Strut Brace

Non-standard steering wheel

Now the only thing to add to this is, it has a Pod (and powerfc). Although its mounted and has a seperator (not a box) between the pod and the engine bay.

The car passes exhaust in ACT and I'm not overly worried about that here, but the pod/FMIC combo seems to worry me from the others experiences here.

Basically - what should i do to the car before taking it over the pits?

The pod will need to go, you can't have 2 intake mods here in Vic. Also, just FYI, alot of police don't care about an engineering certificate. I know you have already had it done, just don't bother with another one. I know people who have still been defected and sent to EPA, so IMO it is a waste of time and money for a daily 'stock-ish' car.

Things like EBC and PowerFC are outright illegal (you may not get caught, just know they are illegal tho)

Hope this helps a bit!

Cheers,

Dan :rolleyes:

I read the whole thread and it didn't look like this was covered. My car has a rwc as of a few days a go and everything is completely stock minus a rear strut bar. I have to take it to vic roads to get registered next week. Now under their policy, import vehicles must be inspected by them before they allow the registration to pass.

Anyone know how thorough this "inspection" is?

Assuming the rwc was infact done properly, i should be fine right?

Got back from a reputable tyre shop and said that wheel spacers are legal if they are bolt on.

I was wondering where i could get a confirmation of this law from vicroads? is there a phone number i can call and ask about modifications like these?

I got defected for wrong tyre load rating on my tyres.

I have two options;

- Replace the tyres on my rims (which require bolt on spacers)

- Or put on a set of rims with tyres which do not require spacers.

Thanks

Patrick

I'm THINKING about running a straight through pipe, what I want to know is how bad is the fine REALLY is for not running a cat? Everyones heard the rumors, but has anyone actually ever heard of getting done?? I'd say there would be a fair few people running straight through pipes around....

Also what is the process? I have more of an understanding that this would be an EPA matter, therefore if a cop pulls you over and happens to look under the car and notice the absence of a cat, surely he isn't going to be able to slap you with a $*insert horrendous figure here* fine on the spot, I would think that he would take photo's and send you to the EPA... by which time you have fitted a workign cat and fixed up all the other goodies.

But what about if you happened to drive through a defect station. Are these run in conjunction with the EPA? Are there people there with noise/emissions testers? Or is it bunch of TMU lads going to town with the illegal mods and the like?

I've tried googling around the EPA website but I can't really find anything of use..

If anyone could shed some light on the matter it would be appreciated. :thumbsup:

tun a straight through exhaust, but keep the cat cover and fill it up with some sort of steel wool to make it seem "full" so if they tap it it wont sound hollow!. Not like they are going to start taking things off your car on the spot!

decat + straight pipe inside will look and sound like(if tapped) a normal cat.. but a cop with half a brain will be able to tell you dont have a cat cause it fkn stinks + the obvious flames if your that unlucky.. but id think he would only epa you cause he cant prove it on the spot i guess?.. your cat could genuinely be fkd and need to be replaced(not including the straightpipe jobby)(insert ash's comment here) i got done by an epa dude setup next to a booze bus.. checked my exhaust with his sniffer thing etc.. i said it was like that when i got the car and got sent to epa no fines etc just did the obvious before i rocked up

Hey guys, just wondering if this car would get EPA'ed. (Not for being too loud but for the aftermarket intercooler with an exhaust?).

"turbo back stainless exhaust system, front mount intercooler, turbo timer, blitz cold air intake"

I've read the documents but not really sure what else get catagorised as another 'air intake'.

I assume "blitz cold air intake" makes in an EPA issue coupled with the aftermarket intercooler?

G'day guys and gals,

Have anyone used BMC carbon airbox along with aftermarket FMIC?

Would i get away with 1 intake mod rule or not?

I'd like to know this before i decide whether to buy it or not.

Cheers

Grant

yep, they're both intake mods so technically you SHOULDN'T get away with it, but that depends on the officer and how he/she feels/knows ect ect...

Ok, thanks for answering my question quickly.

Cheers

Grant

recently got done for a oil breather. i was wondering have any of you guys heard of it?

it seems i keep gettn done for weird things. last time i got defected was because my cooler had to be crash tested for safety (wat a joke)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hey keep the ideas coming, I'm always keen on projects! But, problem fixed!  I got a cheapie ozito scope from Bunnings and had a good look in and around the bearing and sensor hole. I couldn't see a smoking gun but the bearing looked a bit strange, especially when comparing with a new one. I thought the cover had come off the bearing magnets.  Sorry for pics of a screen, I didn't have an SD card.     Good thing I had the old one to inspect. So, given I'm like a pit crew with wheel bearings and luckily I had a spare bearing because I f**ked up my parts order, I decided to just smash it out. Got the old one out in about an hour. So much easier when the parts haven't had a chance to rust together yet. 😂 And, well, found the problem.    In the second pic at about the 8 o'clock position, you'll see what I think is the tip of the old sensor.  The new sensor has definitely been rubbing but it's all intact, just a little shiny so I'm hoping it's fine.  The car brakes perfectly now and no errors.  I think the job took about 2.5h in the end. 👍🏻 I really appreciate the help in here as usual. Thanks guys.
    • I was only looking because I saw some drops on the ground but it wasn't alot. Recently had it serviced will ask the mech to confirm. Find it strange that it looks standard though, can see in another photo of a random box 
    • So...not sure if you know if that has always been there or why you went looking. It could be old damage from a clutch explosion, or even just the gearbox got dropped somewhere along the line. Basically, you should seal it up to stop oil and dust getting into the bellhousing, but it doesn't matter too much and is not structural. I'd suggest something like a glob of JB Weld. BTW what gearbox oil are you running, I would guess the breather has been spewing it everywhere.
    • Hey Duncan thanks for your reply. Sorry mate I know the photos are shit.  Took another photo for reference. Seems the casing does have a hole in it looking on the net, fluid seeping out. Added a photo   
    • Very hard to make out what you mean, is it the squarish hole with redline shockproof (probably) under it? Is that pic from on top of the engine with the firewall to the left of pic and engine to the right? Either way, spray the area liberally with degreaser and try again, maybe circle the part you are worried about
×
×
  • Create New...