Jump to content
SAU Community

Recommended Posts

Hey guys i wanna dose my Rb25 R33 but im not 100% sure how to do it and can it damage my turbo?

From what i know all you need to do is get a 2.5inch meteal pipe and run it to the mouth of your tubo (the Fan) is that all i have to do? thanks guys.

Edited by Woody23
Link to comment
https://www.sau.com.au/forums/topic/156869-how-do-i-dose-my-car/
Share on other sites

yeah. move the afm so the air coming back thru doesnt throw out the readings. then either run the turbo without any intake, or run a 2.5inch metal pipe. and block the bov.

or you could just simply block the bov for the same effect on the cheap. it wont be as loud or as drivable. ie stalling and running rich issues.

you will get the best dose performing the following mods:

MOD 1

Then add the following for the complete effect.

MOD 2

I like "MOD1" the most, ive got a few bags of sand lying around the shed somewere, might give it a try on my car tonight :)

:laugh:

this is actually true, its done on heavy machinery/ diesel engines that idle for long periods of time so the rings fail to give a good seal on the cylinder liners, so they rev the engine up and let it draw in AJAX cleaning power and it acts as an abrasive which in turn re-hones the bores giving it an engine rebuild in a can so to speak.

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Bah! I can't see the point in custom number plates at all. I went to the rego office, fished through a box of "premium" plates (the ones that had the "not as tall" option for the front plate) and picked the one that had a 32 in it. That's the limit of the effort and cost I will put into number plates. The only plate that I'd consider paying for would be 2332, but that's not possible here because it already exists from probably 90 years ago, and it would cost a fortune to obtain it, if it were available.
    • After chasing my tail with LS results..... and cheaper than a turbo swap... How confident are you that the dyno is accurate relative to other results? How fast is the car - What MPH does it actually run? Is this similar to what people running this power would expect?
    • Hi mate I am having an identical issue with my 98 R34 GTT. The engie suddenly cuts out under load at about 3-4k, black smoke out exhaust. Almost feels like traction control kicking in. No CEL but still going to check codes later today. Car was sitting in the shed for about 5 months before hand and only idled a few times, took her out with about 1/4 tank, filled up and thats when the issues started happening.  Threw on a spare set of coils/harness and checked plugs which was no help. Recently had fuel pump/filter changed so surely thats not the issue unless condensation in fuel, I just havent had the time to drain it It's running a hi flow turbo, bosch 1000cc injectors, walbro 450L, Z32, Nistune etc... All about 2000km old.
    • I always wonder where the obsession with legal/illegal spacing on number plates in the UK comes from. Because it comes up in comments in every UK-based video I see on youtube. From my point of view all of your plates look a bit odd. Just because there are no markings whatsoever. In Australia we have the state that has to be on it. In Europe you get stamps and state logos. Yours look a bit like a throwaway draft that people then stuck with. And attached with blu tack so that it falls off at the slightest disturbance. Not trying to hate, but it's interesting how things are done in different countries. Do you have to follow a lettering convention when choosing a custom plate?
    • Hybrid sounds like a supercharger... It's half a turbo, with a belt to drive it! Oh wait, they're just called super chargers...
×
×
  • Create New...