Jump to content
SAU Community

Recommended Posts

Q; What is the difference between a series 1 and series 2 R33 Gtst?

A; There are several differences...

  • The front end of the series 2 is sharper, slimmer headlights, different front bar (indicators and fog lights are round and located at the bottom of the bar). The bonnet has much sharper ridges.
  • The "skyline" panel at the rear of the car is body coloured on the series 2.
  • The interior of the series 2 has been updated including different trim, a passenger airbag and the dash facia has been updated.
  • Mechanical differences include an updated ECU and a ceramic turbo.
  • The series 1 was in production from late '93 through to late '95. The series 2 ran from early '96 through to early/mid '98.

Link to comment
https://www.sau.com.au/forums/topic/17349-r33-gts-t-series-1-and-2-differences/
Share on other sites

  • 8 months later...

Also the S1 has an ignitor located on top of the motor at the back on the rocker cover near the firewall, whereas the S2 has the ignitor built into the ECU. Another small differance is the headlight backings, where S1 has black backing and S2 has chrome backing.

  • 1 month later...
  • 3 weeks later...

There are some similarities though, i believe the 'different wing' on the Series II (think it's called an M-Spec?) also appeared on some of the series I (or 1.5) 33's as well. Plus the other day i saw the lower stock R33 Series I wing on a car that had the Series II skyline imprint on the boot, and not the panel of plastic. This may have been custom though.

here is something else for you, in 1995 there was a series II also, it had the series I front, but had the series II engine, dual airbags, colour coded rear skyline badge, updated interior, different seat trim to 93-94, not the same as 96, series II instrument panel, series II floor mats.

  • 3 weeks later...

Here's what my '95 R33 has, which is still a bit different again. Not sure when it was made other than 1995.

Series 1 - front bar, steering wheel, with airbag, interior (velour) but with updated pattern (not quite as dark), rear badge (clear plastic and silver letters, not colour coded).

Series 2 - wing, engine, boot lid badge (titanium)

??? - instrument cluster (I wouldn't know the difference), suspension

??? - grille (which I quite like) that's kind of like a rounded GTR grille rather than the slat style of most that I've seen. I think this was just a factory option though, I've seen very few around, and some '95 models with the slat grille.

NO passenger air bag

And while we are dumping shit on other people's Skylines, I would just like to say that the indicators on the Series 2 front bar look like huge blocks of Lego (blerghhh!) :)

everyone mixes answers to which turbo is which up

this is the difference.

the series one AND two exhaust wheels are ceramic, and prone to delaminating from the shaft, due to excess heat and resistance, resulting in bits of tubo stuck in your cat :)

The difference is in the intake side.

The intake wheel of a series one turbo is steel, where in a series two (and even r34 gtt) has a nylon wheel. this results in a quicker spool up.

the problem is not with the intake side of the turbo, its the exhaust, so if you had to compare the two, the series 1 turbo is no less likely to fail than a series 2 turbo.

Ive just about finished putting a motor out of a series 1.5 into my series 1.

dunno if anyone cares, but the clips for the coil packs are a bit different, so i had to swap them and the harness from my blown series one motor and put them in the series two, but again, dont know if anyone cares about something so trivial...

  • 4 months later...
  • 3 weeks later...

i know i've gone thread digging but i wanted to know if anyone has heard of a series 2 being made in 1995. not a series 1.5 but a full series 2??? and do people commonly find importers reffering to 1.5's as series 2???

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • This. As for your options - I suggest remote mounting the Nissan sensor further away on a length of steel tube. That tube to have a loop in it to handle vibration, etc etc. You will need to either put a tee and a bleed fitting near the sensor, or crack the fitting at the sensor to bleed it full of oil when you first set it up, otherwise you won't get the line filled. But this is a small problem. Just needs enough access to get it done.
    • The time is always correct. Only the date is wrong. It currently thinks it is January 19. Tomorrow it will say it is January 20. The date and time are ( should be ! ) retrieved from the GPS navigation system.
    • Buy yourself a set of easy outs. See if they will get a good bite in and unthread it.   Very very lucky the whole sender didn't let go while on the track and cost you a motor!
    • Well GTSBoy, prepare yourself further. I did a track day with 1/2 a day prep on Friday, inpromptu. The good news is that I got home, and didn't drive the car into a wall. Everything seemed mostly okay. The car was even a little faster than it was last time. I also got to get some good datalog data too. I also noticed a tiny bit of knock which was (luckily?) recorded. All I know is the knock sensors got recalibrated.... and are notorious for false knock. So I don't know if they are too sensitive, not sensitive enough... or some other third option. But I reduced timing anyway. It wasn't every pull through the session either. Think along the lines of -1 degree of timing for say, three instances while at the top of 4th in a 20 minute all-hot-lap session. Unfortunately at the end of session 2... I noticed a little oil. I borrowed some jack stands and a jack and took a look under there, but as is often the case, messing around with it kinda half cleaned it up, it was not conclusive where it was coming from. I decided to give it another go and see how it was. The amount of oil was maybe one/two small drops. I did another 20 minute session and car went well, and I was just starting to get into it and not be terrified of driving on track. I pulled over and checked in the pits and saw this: This is where I called it, packed up and went home as I live ~20 min from the track with a VERY VERY CLOSE EYE on Oil Pressure on the way home. The volume wasn't much but you never know. I checked it today when I had my own space/tools/time to find out what was going on, wanted to clean it up, run the car and see if any of the fittings from around the oil filter were causing it. I have like.. 5 fittings there, so I suspected one was (hopefully?) the culprit. It became immediately apparent as soon as I looked around more closely. 795d266d-a034-4b8c-89c9-d83860f5d00a.mp4       This is the R34 GTT oil sender connected via an adapter to an oil cooler block I have installed which runs AN lines to my cooler (and back). There's also an oil temp sensor on top.  Just after that video, I attempted to unthread the sensor to see if it's loose/worn and it disintegrated in my hand. So yes. I am glad I noticed that oil because it would appear that complete and utter catastrophic engine failure was about 1 second of engine runtime away. I did try to drill the fitting out, and only succeeded in drilling the middle hole much larger and now there's a... smooth hole in there with what looks like a damn sleeve still incredibly tight in there. Not really sure how to proceed from here. My options: 1) Find someone who can remove the stuck fitting, and use a steel adapter so it won't fatigue? (Female BSPT for the R34 sender to 1/8NPT male - HARD to find). IF it isn't possible to remove - Buy a new block ($320) and have someone tap a new 1/8NPT in the top of it ($????) and hope the steel adapter works better. 2) Buy a new block and give up on the OEM pressure sender for the dash entirely, and use the supplied 1/8 NPT for the oil temp sender. Having the oil pressure read 0 in the dash with the warning lamp will give me a lot of anxiety driving around. I do have the actual GM sensor/sender working, but it needs OBD2 as a gauge. If I'm datalogging I don't actually have a readout of what the gauge is currently displaying. 3) Other? Find a new location for the OEM sender? Though I don't know of anywhere that will work. I also don't know if a steel adapter is actually functionally smart here. It's clearly leveraged itself through vibration of the motor and snapped in half. This doesn't seem like a setup a smart person would replicate given the weight of the OEM sender. Still pretty happy being lucky for once and seeing this at the absolute last moment before bye bye motor in a big way, even if an adapter is apparently 6 weeks+ delivery and I have no way to free the current stuck/potentially destroyed threads in the current oil block.
×
×
  • Create New...