Jump to content
SAU Community

Recommended Posts

I was just told there is a massive defect station on Maroondah Hwy outside the cop shop.. not sure what suburb that would be??.. but maybe avoid driving down there at all..

That would probably be the Blackburn/Mitcham area, cant think of anywhere else where the cop shop is on that road

spotted Chris in the gtr and Min in the Stag going down sydney rd just before craigieburn

thumbsup all round :whistling:

then a silver 33 gtr from tassie turned out of donnybrock rd and was going down hume highway

some fine cars on teh way to dutton :whistling:

Blue R33 GTS with Nismo wheels on middlebourgh Rd Doncaster

Blue R34 GT-R, looked stock, turning into blackburn Rd Blackburn

White R32 GT-R in the Dandy hills on Saturday, He gave me the thumbs up so I waved back.

All spotted on Fri

Spotted a Blue? R32 - plates UAD-XXX - around 3:15am turning off Tullamarine Freeway onto Bell Street.

Also spotted a Gunmetal R33 - plates UUQ-XXX - around 4:00pm passing my work on Apollo Drive.

parked opposite of rekin (uie710) today. always see ur car at eng carparks.

wat u studying dude?

haha yeah i saw your car there.

Studying Industrial Engineering & Engineering management (IEEM) 3rd year atm.

Course has been cancelled at uni, im the last group doing it :wub:

How bout your self? Get some sau-vic stickers :down:

I was just told there is a massive defect station on Maroondah Hwy outside the cop shop.. not sure what suburb that would be??.. but maybe avoid driving down there at all..

It wasn't a defect station and it wasn't outside a cop shop. It was a drug bus in Ringwood, I got waved through.

The blitz was happening near Maroondah Highway and Rooks roads (Mitcham). Apparently cops and vicroads were pulling over a shitload of people like no tomorrow.

I hope no-one got dicked....

Really? I went through there and there was nothing.

Edited by llama_au

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...