Got Over 400kw Atw?

[Rolls]

For it to be closed loop it will need a signal input from the camshaft position sensor that you will need to install. You can't just use RPM as an input for closed loop as it's unrelated to what you are adjusting

I thought he was talking about open loop control, but yes if closed loop you obviously need an input as well.

[STATUS]

and you probably couldn't run them with a vipec either.

think evo, vipec / link no issues having fully variable cam timming.

[XRATED]

We are looking into an rpm box for you guys.

I've been using the msd rpm switch for a while now... sturdy bit of gear.

I'm suuuper keen to get a hold of 25 VCT conversion parts and camshaft from you once it's all sorted. I'm suprised no one has developed it yet???

Do greddy still make the adjustable cam sprockets for the 25 vct cam gear?

sign me up-

Cheers

Justin

[The Dan]

I've been using the msd rpm switch for a while now... sturdy bit of gear.

Do greddy still make the adjustable cam sprockets for the 25 vct cam gear?

I'll look into that thanks.

The factory RB25 inlet gear is adjustable....it's just on the back of the gear

I have seen someone do a bolt configuration through the gear so it was adjustable from the front.

[The Dan]

The MSD RPM switch looks like it only turns something on at a specific RPM? We need to turn it off again at a certain RPM so that means it would need to be programmable

[SimonR32]

The MSD RPM switch looks like it only turns something on at a specific RPM? We need to turn it off again at a certain RPM so that means it would need to be programmable

Look for a MSD RPM window switch, a RPM Switch is on... A window switch is on and then off

I'm just using a on switch mind you, works fine

[Rolls]

eboost street comes with a window switch built in as well.

[The Dan]

Look for a MSD RPM window switch, a RPM Switch is on... A window switch is on and then off

I'm just using a on switch mind you, works fine

Thanks.

They seem to be what we were looking for. And only about $150 so also the right price.

[Beer Baron]

what intercooler, are you running??

His car has the basc 70mm ARC GTR intercooler. They're a good bit of gear. Light, good flow and good cooling. They are actually lighter than a stock GTR intercooler!

[Walk510]

think evo, vipec / link no issues having fully variable cam timming.

i was pointing more at v8 vvt that run 4 cam sensors

like the bmw's and soon to be nissan v8's

[STATUS]

i was pointing more at v8 vvt that run 4 cam sensors

like the bmw's and soon to be nissan v8's

run them as pairs in/in ex/ex not often you want different valve timing event between left and right banks.

[XRATED]

Thanks.

They seem to be what we were looking for. And only about $150 so also the right price.

This is what I use:

http://www.msdignition.com/Products/RPM/Timing_Controls/RPM_Controls/8969_-_Digital_RPM_Window_Switch.aspx

Cheers

J

[3.olGTR]

got a 94 gtr 3.o litre bottom end 2000 id injectors 260 cams gt 2860 -10 turbos just over 400 on 16 psi can run up to 26 psi

[jet_r31]

eboost street comes with a window switch built in as well.

Woudn't trust a eboost to switch anything on, they are a POS at the best of times

cheers

darren

[Rolls]

Woudn't trust a eboost to switch anything on, they are a POS at the best of times

cheers

darren

Mines works great, what is the issue you have with them?

Controls boost well, window switch works great, lots of people recommend them?

[The Dan]

Mines works great, what is the issue you have with them?

Controls boost well, window switch works great, lots of people recommend them?

I've never had problems with the unit or the solenoids on, only the people who wire them in incorrectly. I'd say most people's grief would be caused by the same thing

[jet_r31]

Mines works great, what is the issue you have with them?

Controls boost well, window switch works great, lots of people recommend them?

They have a bad habit of just locking up , outputs stop working at same time and you have to send them back and get them updated.Eboost 1 and 2 do it. ... I am not the only

one who had that problem, a mate had the same problem , and if you look around, a lot of the sport compact racers have had the same problem

Its actually quite common and a lot of workshops won't use them for that reason, as i found out after mine f**ked up.

Not good when its hooked up to your water injection solenoid that for sure

I wound't buy a second handy of ebay, thats for sure!

When it worked it did do a awesome job of boost control, funnily enough mine got stolen out of my car when some work was getting done to it, before i had a chance

to get it updated, hopefully it blows the thiefs car up ..lol

cheers

darren

Edited July 18, 2011 by jet_r31

[Chopstik]

anybody using 2860 -5 and achieve these powers??

[SS8_Gohan]

i've got 2530's, which are almost identical, and with baby cams still managed 400rwkw with E85, only 21psi as well - most people run 260 cams, and prob more around 24psi is the pistons/everything else can take it, you'll walk in the 400 with -5's

[Chopstik]

nice!!!