Jump to content
SAU Community

Recommended Posts

Trap speeds arent too far off Martin. Were you getting wheelspin in 1st?

I am interested to find out what would happen if we both took our cars to a roller dyno somewhere, along with a volunteer who can bring his/her 300rwkw car..

What is boost recovery like in gear shifts? Does your car have a screamer pipe? Hard to tell from the clip

It takes a little over a second until its back on song for mine.

Yeh wheel spin in 1st when I launched, otherwise I was bogging down.

Let me know when you're thinking of going down again, would be good to compare on the night. Trev, you get up here too! :P

Nice work on the run hanaldo. Sounds exactly like mine and landscribble's. Same sort of runs, and trap speeds. Mine was doing the same thing, either bogging or wheelspinning, so I definitely need a lot more practice at taking off, it's quite the balancing act. :)

What Lithium said is interesting, because my friend with a standard turbo r34 always goes on about how laggy it is between gears boost wise. I'll try find a video of my run and then post it up.

Also, geez you're revving that rb25 high! :P

Also for people whom's interested in to twin pulse turbine housings. I'm in the process of making one that has a working VNT valve. It is made to work with a single or twin pulse manifold. Designed to switch a .41 A/R turbine housing into .82 after boost pressure rise beyond 12psi, it should dynamically advance down low torque and power while not hurting mid and top end.

will post up photos once its complete.

I'd be super keen to test one... ss1 or ss1pu external gate for a split pulse manifold.

Cheers

Justin

Well it tended to be like that in 1st with the pro-tree, I wasn't getting off the line very well and bogged down a fair bit in 1st. 2nd is hard to tell cos the V8 next to me starts to make a bit of noise. From memory it was straight onto full boost in every other gear though... I'll have to take it for a drive and pay attention to the boost recovery.

What would that indicate though? At the moment I'm aware I have either a restriction or possibly a cam timing issue.

Could be turbo design, boost leak, some kind of restriction - is it ball bearing? What was the temperature like on the day by the way? Also, what kind of dyno was it tuned on? One of the reasons I said anything is mine was trapping higher and running quicker times (14.0 @ 110mph even with a TOTAL bogged launch - ~3s 60ft, then missed second gear completely etc when a mate who has a stock turbo R33 had a go) with ~260-270kw @ hubs on 15psi and going by most people here's comments etc that power should be about equivalent to 240kw "Oz dyno" type numbers.

Regardless, I remember when I was running 108-109mph in my car - doesn't make for a slow car by any means, no doubt well worth being happy with but in one way or another it potentially could be a bit quicker with that power.

It will be interesting to see what my car traps.. If it exceeds 110mph or not.

When planning the build I'd always hoped it would get close to 120mph, but these G3 results have got me guessing now..

Time will tell.

It will be interesting to see what my car traps.. If it exceeds 110mph or not.

When planning the build I'd always hoped it would get close to 120mph, but these G3 results have got me guessing now..

Time will tell.

Your car should pull at least 118mph trap speeds at 235kwatw on unigroups dyno

As my car when it had 231rwkw pulled 118mph and my brothers car with 225rwkw pulled 116mph both tuned by Unigroup very conservative dyno

Once you get it retuned on a cooler day and put abit more boost in should pull over 120mph

When your heading out to wsid let me know keen to try my car out aswell

It will be interesting to see what my car traps.. If it exceeds 110mph or not.

When planning the build I'd always hoped it would get close to 120mph, but these G3 results have got me guessing now..

Time will tell.

I am guessing 115-118mph...

Thanks man!

I'll let you know for sure. The gearbox input shaft seal shat itself on the dyno, so I'll need to fix that before I hit the drags otherwise I might just ruin the clutch. Wont be too long.

I hope so Lith :) would be nice to get a respectable result from it.

Congrats on being able to sell an R33 Troy. Not many people can accomplish that.. lol

My only experience with Drag racing was with an S14.

175rwkw (unigroup dyno)

stock turbo with bolt on mods and boost.

Stock Clutch.

17 inch wheels with 255s on the back and let the air down to 22psi

best it ran was a 13.8 @ 107mph with a 1.8 60'

I'd say you'll crack 13s with practice.

Thought about launching in 2nd gear?

Altering comp wheel size little over or under makes no differences, it doesn't mean it has to be a 73mm, I haven't never seen their turbos before, so blade profile will be totally different. Any results from that on a Rb25det?

RB25s arent for me!

But like all billet wheels the shank is way smaller so combined with the 5mm bigger compressor and blade design it flows way more. They make 320-340awkws on EVOs in the US on pump fuel with about the same if not better response than 20G.

They do a bigger compressor bersion around 76mm but they dont use the L2 turbone for that...they go the TD06H

Roy im fairly sure the FP red's 65mm turbine isnt a trimmed TD06H, im fairly sure its a modified Sierra wheel.

I doubt they are going to give away the info either way..

Is your 73HTA running yet?

FP stuff has hardly ever been used on RBs, there Bri73y on here is putting a 76mm FP HTA turbo on his RB25 and aims to have that tuned in a few weeks time. FP rate their 73mm HTA compressor wheel to 54lb/min and don't tend to be over optimistic with their flow ratings.

Here is an example of their 73mm wheel on a GT30 http://www.ringer-racing.com/product.sc?productId=412

They do a range ot Evo based turbos, STI based turbos, Garret based turbos and Hi-Flow turbos....their range of 55, 65, 68, 71, 73, 76, 82, 86, 105mm wheels..I cant imagine to know the combos of turbiones and compressorss they offer and have tried and wont offer.

The R32 is right behind the Cossie rebuild whcih shoudl be getting puched out this weekend and in for tune/run in next week. The R32 is right behind it for a tune

Usually it's when you miss the selection - so often miss-timing the clutch movement, or not fully putting it through the gate and ending up in neutral. Sometimes dodgy sychros, too excited or slight retardation

RB25s arent for me!

But like all billet wheels the shank is way smaller so combined with the 5mm bigger compressor and blade design it flows way more. They make 320-340awkws on EVOs in the US on pump fuel with about the same if not better response than 20G.

They do a bigger compressor bersion around 76mm but they dont use the L2 turbone for that...they go the TD06H

That is a cropped version of the TD06 turbine, that would shift power band to mid high range. It increases the total dispatching area of a turbine wheel. I used to crop the Sierra S3 turbine wheels for high flow before the current, on stock R33 21U turbine, at 16 degrees that reached 275rwkws while 250rwkws on 12 degrees. noticeable difference in drivability from Std to 10, 12 and 16 degrees crop, the higher the worse.

Shank (hub) sizing increases total induction area, also generates that nothing then hard lunch effect, might be good for drag cars, how ever on road I'll reduce that to minimum. I'm making 2x new wheels for the SL2 turbine, one is a altered SS2 wheel with tall blade profile, while the other one comes from the 3rd trail SS3.

Above is only based on stock camed Rb25det engines, larger / different engines might act differently.

The new SS2 comp should pickup another 20kws without altering current response, while the SS3 comp would be plenty for stock Rb25det's cams, while shifting mid range towards the left by around 200RPMs.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...