Jump to content
SAU Community

Recommended Posts

Pulled up behind a grey 34GTT at Glendenning BP just after 6PM tonight.

Then a maroon S1 r33 gtst came boosting through the carpark and decided to rip hellies at the T intersection near entrance. You sir, are a dead set d*ckhead and the reason why the rest of us get hassled by the cops

White R33 gts-t at Moss Vale shops with SAU sticker on rear right 1/4 window. Duck spoiler and black rims.

Provided a nice soundtrack to accompany my pre-court coffee!

OMG thats me.

Been spotted again.

can anyone tell me what type of tail light these are and where i can get some?

i want a pair :)

They are just the LED rear tail lights for R34, type that into ebay you will find plenty available.

They are just the LED rear tail lights for R34, type that into ebay you will find plenty available.

I remember having a look around few months ago on ebay,

there's a large selection, but would most of them look the same in terms of the crystal LED look (whilst the lights are off). I know there's different actual LED pattern styles when the lights are on.

White R34 GTT with R34 GTR wheels at Robertson's pie shop around 4pm on Saturday.

That was me, 1st time spotted !

Bought a few bits off ebay picked em up at Albion park, turned out this guy was the original owner of the car and the bits i won were off my car!!!!

I couldnt believe it, sister lives at moss vale so went for a visit.

I remember having a look around few months ago on ebay,

there's a large selection, but would most of them look the same in terms of the crystal LED look (whilst the lights are off). I know there's different actual LED pattern styles when the lights are on.

Aggroman (Dave) is making a retrofit kit to go into your existing housings, that matches the pattern and brightness of the Nismo GT LEDs, hit him up for details

Spotted a silver or gunmetal R34 GTR on Old Windsor Rd while I was at the lights to Norwest Private around 5.30pm today. :thumbsup: That's my next serious Skyline once the kids get abit older!!!!

I spotted a stickered-up R34 GTt parked right behind me today when I was at CostCo. It was white with a shopping list and Nismo stripes down the sides.

Unfortunately I was in the old man's car and not my own.

Hi

I feel slack i have not been on here for a really long time so i am sorry to all who have posted they spotted me. Also i have been getting heaps of waves lately i am sorry if i have a delayed reaction usually listening to music and just in a world of my own when im in my baby!! My plates are JDM034 if anyone has seen me crusing around!

Have seen so many skylines lately......unfortauntly there is a green P plater white R34 gtst driving around Raby your sending everyone INSANE you need to slow down and stop waving to me whilst you hammer it around corners you look stupid and i dont feel like watching you crash!!!

Wasn't a R33 by any chance? I don't floor it everywhere, but I take my corners pretty quick (I just love to :P), green p's and N/A, looks like a gtst though, also live in Raby. What side do you live on? Near the school or the shops?

Black R33 on the side of the M5 around 1.

And a white R33 S2 in the car park at MacArthur Square this arvo.

First spot, White R33 S2 :D

Edited by S3RK
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...