Jump to content
SAU Community

Recommended Posts

And it's on low boost

I'm sure it would crack 300 if the guys at JEM felt okay pushing more boost into it. But again they have their reasons for not doing that.

Waiting on a payment for a set of rims I sold then I should be able to show some water meth results to people interested in what it can do with ping resistance.

  • Like 1

Well the ching ching cooler is doin a good job because the outlet pipe up till a bit past the battery tray is nice n cool, BUT once you reach the rad/fan area it heats up pretty quick all the way to intake mani. So I know its not the cooler thats why I wanted to re-route and heat wrap that bit of top pipe away from rad/fan and cam covers

Mines the same on stagea, hot as f**k on that corner and side piece, then water is injected near the BOV , after that its cooler..

i was making 641nm, so looks like the two turbo's are similar on that boost, not sure about the housing differences though..

its a good result though, looks like 16psi, probably needs atleast 20psi to really unleash

Thats a pretty good point, I realise that I'm making 286rwkw on 16psi not 18psi, as it drops down to 16 up the rev range where the power peak is, so its a good figure, what will happen at 20-22psi I cannot wait, or 26psi if I add water injection.. :) 2nd gear can be pretty scary, even with a moderate stab at 4000rpms it gives a nasty lurch forward and skates sideways / wheelspins about a bit, 3rd gear same story but to a lesser extent, am running good compound tyres 18" Potenzas at the rears.. lurving it man... My dynocurve shows that it shoots up 100rwkw in about 400-500 rpms (from 100 to 200rwkw), this the bit thats fun... :yes:

Thats a pretty good point, I realise that I'm making 286rwkw on 16psi not 18psi, as it drops down to 16 up the rev range where the power peak is, so its a good figure, what will happen at 20-22psi I cannot wait, or 26psi if I add water injection.. :) 2nd gear can be pretty scary, even with a moderate stab at 4000rpms it gives a nasty lurch forward and skates sideways / wheelspins about a bit, 3rd gear same story but to a lesser extent, am running good compound tyres 18" Potenzas at the rears.. lurving it man... My dynocurve shows that it shoots up 100rwkw in about 400-500 rpms (from 100 to 200rwkw), this the bit thats fun... :yes:

try this, find a nice smooth piece of tarmac, let second gear come up to 4000rpm without boost, then drop the hammer and fry them for 60meters ,

awesome feeling, lol oh and PRIVATE ROAD obviously :)

Edited by AngryRBGTX

try this, find a nice smooth piece of tarmac, let second gear come up to 4000rpm without boost, then drop the hammer and fry them for 60meters ,

awesome feeling, lol oh and PRIVATE ROAD obviously :)

hahahah..now that you told me, I will definitely try that out. Why are you only running 16psi on E85 (your signature), go 26psi.. Hey you the same guy as sliver33 something right?

hahahah..now that you told me, I will definitely try that out. Why are you only running 16psi on E85 (your signature), go 26psi.. Hey you the same guy as sliver33 something right?

yeah i changed my name, well the usual advice is 300kw is the limit for stock bottem end so with that in mind 320kw is a good number and looking very safe on E85, i like to stay cautious rather than see how long the piece of string is... lol.

You should go E85 next, cost me around a grand extra.

yeah i changed my name, well the usual advice is 300kw is the limit for stock bottem end so with that in mind 320kw is a good number and looking very safe on E85, i like to stay cautious rather than see how long the piece of string is... lol. Plus im working on a new project, got a cheap XR6 ute which im thinking bout turbo conversion :)

You should go E85 next, cost me around a grand extra.

i have never read my name so much on a forum before.

update jez has already told most of it but i will do it again anyway.

setup so far has put up with a drag session, private track day , 2 SAU cruises ,my wedding and a bunch of other driving.

i have been watching temps and oil use like a hawk, engine still seems very very healthy, min amount of breathing and so on.

and yes my old BOV which we installed before wakie was a massive leak no wonder it felt not as fast.

all leaks are now fixed and skybitch is better then ever thanks to jez.

below is the print out

post-57423-0-91542900-1357804481_thumb.jpg

Its very interesting to see the numbers being made with a 0.63 rear housing on the 5558, ill have to look into this more before ordering one, but is there anyone running a 0.82 rear?

I'm over the moon with how much power the baby turbo put out the best part is it made the exact power I wanted

Going off of the road speed between kurtis and jez's graphs there doesnt seem to be that much difference between when they are on full boost.

I remeber reading somewhere that Kurtis' setuo was all in by like 3750rpm but cant recall what rpm jez was hitting full boost.

If the difference is negligible, youd almost go the ts .84 6262 just for the extra power it gives

I'm over the moon with how much power the baby turbo put out the best part is it made the exact power I wanted

Hey Kurtis, with that much power you could put down a high 10s quarter mile? Not sure why you got a 13.098, guess tyres/suspension/launch was the problem. I have yet to learn how to launch..

Anyone done any back to back (or similar) on the 6262 and 6266? Will be deciding between these in 0.84 TS for a 2.2 VE SR. Leaning towards the 6262 atm.

i have seen dyno sheets floating around which are probably in this post somewhere anyway - which show the difference in the response between, 6266, 6466,6766 being about 500rpm on a 3.4L ...

I have even emailed precision directly who have confirmed that it would be about 300-500rpm on a 3L

i have seen dyno sheets floating around which are probably in this post somewhere anyway - which show the difference in the response between, 6266, 6466,6766 being about 500rpm on a 3.4L ...

I have even emailed precision directly who have confirmed that it would be about 300-500rpm on a 3L

If you looking for a 3076R equivalent then go the 0.63/ 5558 which is what I did from research and Unigroup's advice, if you looking for bigger, then consider the 6XXX series...

Hey Kurtis, with that much power you could put down a high 10s quarter mile? Not sure why you got a 13.098, guess tyres/suspension/launch was the problem. I have yet to learn how to launch..

I can explain my time , first time drag racing ever.

Still had suspension setup for corners .

So basically driver error but hopefully with practice I will put a time to match speed but aiming for higher speed as well.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm so far behind in the jobs I have to do at both work and home (including car) that I have become immortal. There's simply no way that I can die now.
    • Each to their own I guess  Me, I put just as much time into cleaning inside of the cars as I do on the outside As for getting wet, it is really no different than steam cleaning the carpets at home, apart from the cars carpet dries alot faster than the house, again, I only do it in the hotter months and leave the car opened up for a few hours As I only do it yearly, it is just before I do the diff and gearbox service, so I clean the carpets, then it's up on stands, wheels off, service, clean the undercarriage,  grease the bushings and do a nut and bolt check on everything  Disclaimer: I typically had all the time in the world to kill when I was working 🤣, so spending a full day or 2 cleaning, serving and "looking at stuff" was,  easily achievable, and a fun mental therapy day As for time to kill, I retired last Wednesday, so apart from my physical training, my days are filled with lots of random jobs around the house and garden...."Idle hands are the Devils something something" I am also buying a new house sooner rather than later, I'm actually looking at a potential property tomorrow, I'm looking forward to getting a car hoist as I'm starting to get to old to crawl around under a car, I can only imagine all the undercarriage cleaning and looking at stuff when that gets set up
    • Yeah, I'm not interested in wetting the carpets, and I don't care about brown dirt/dust that lives deep in the pile or underneath. It's not like I crawl around on them in my birthday suit or eat dropped food off them (because there is never any open food in my car). The seats are alcantara (cheap Chinese imitation alcantara, to be sure!) with barely 1" of foam pad behind the surface. That's not getting wet either. Any car that I would be happy to get the interior wet, I would not care to put the effort into.
    • We have one that holds 2.8L of water. On floor carpet that hasn't been touched in 2 or 3 years, will take a minimum of 2 fills of the tank to do a bedroom, and that's going AROUND the bed.   In the cruiser, I used an ENTIRE 2.8L tank, just on the front passenger footwell. But it had some fungus growing, and had been full of mud from being used as a 4WD for many years. I can do that floor again, and it will still pull mud out. However, the water now only looks dirty, not pitch black and leaving full sludge in the bottom of the tank it sucks back into. Oh, and, this is about a $1500 unit.
    • This is mine, works a treat for the cars, suction is good, I use the Bissell clean and protect stuff I have found giving it a good spray and light scrub with the soft brush on the head of the nossle for carpet, and a rub with a microfibre for cloth seats and cloth door trims, prior to another quick spray before vacuuming it up works the best @GTSBoy You would surprised on what it gets out of carpet and seats that actually "look" clean, I recommend that you test drive yours when you have a little time to kill, then post pics of the muddy looking water that I believe you will find
×
×
  • Create New...