Jump to content
SAU Community

Recommended Posts

yep theres a guy on the commodore forum thats doin it. just for the record holden made a ltd edition monaro with the awd. its called a coupe4. the dude from HPF put a big ass turbo on a coupe4. i cant remember how it went.

The problem with the Coupe 4 was that holden only made them as autos due to them being worried about people smashing the drivetrain to pieces doing big limiter launches.

Personally i would love to see a big power Coupe 4 manual. I'm sure it would have been done, just havn't come across one yet. Trent you ever seen one?

i wonder if anyone has taken the adventra running gear and put it in a commodore shell, turbo/supercharged 4wd V8 power

I was thinking of doing that a while ago on top a VP Wagon full sleeper. But then I did some research into the 4wd system and it is beyond crap always breaking especially if you tried to put more power through it than stock. I really wish it wasnt crap because it would of been a brilliant project.

i would be proud to have that parked in my driveway, i reckon the stance, the graphics even the rear wing look agressive yet sleek... regardless of engine type.

yeah I love it! very cool. would be great. nice big 4 door commo, with a screaming 350rwkw 26 in there. should be a fun car and it looks and must sound great too.

yep theres a guy on the commodore forum thats doin it. just for the record holden made a ltd edition monaro with the awd. its called a coupe4. the dude from HPF put a big ass turbo on a coupe4. i cant remember how it went.

rob vickery had the red one, standard motor with a turbo kit. he sold it to the guy that owns BLO402, cant remember his name right now. it runs 12's from memory *ninja edit, guys name is gary pope*

theres one up in sydney, 400+cu stroker, turbo, running high 10's in FULL street trim

Edited by VB-

i saw a VU ute at easter nats a couple of years back, blending in as they do, and was about to walk straight past when i saw an rb26 parked in the engine bay.

i did a double take and yeah, it was a 26 with a high mount and a cooler and what not. pretty cool.

then the owner came back, looking for all the world like corey worthingtons older brother with big yellow sunnies, cap sideways, dollar signs around his neck, a heap of jewelry, and just generaly looking like a douche. worst part was he had two smoking hot birds with him *shakes head*

anyway started talking to him and he'd blown his gearbox doing skids, which is all any 'nats is good for. he was running a 3spd auto *double face palm*

rowdy

i saw a VU ute at easter nats a couple of years back, blending in as they do, and was about to walk straight past when i saw an rb26 parked in the engine bay.

i did a double take and yeah, it was a 26 with a high mount and a cooler and what not. pretty cool.

then the owner came back, looking for all the world like corey worthingtons older brother with big yellow sunnies, cap sideways, dollar signs around his neck, a heap of jewelry, and just generaly looking like a douche. worst part was he had two smoking hot birds with him *shakes head*

anyway started talking to him and he'd blown his gearbox doing skids, which is all any 'nats is good for. he was running a 3spd auto *double face palm*

rowdy

that cars been for sale for ages claiming to have 1100hp.....

woah... an RB in a commodore. I'm sure that's a first :P

</sarcasm>

I would seriously be impressed if it was a VE commonwhore though. I can't stop myself from thinking they look awesome. Unfortunately unless they're packing an LS1 or LS7 they're kinda disappointing to drive.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...