Jump to content
SAU Community

Recommended Posts

Rather than making a new tool thread, any comments on this for getting off flywheel bolts? Would it be up to it? $169 on sale for jap made rattle gun, 425ft/lb (so about 575nm?). The $40 supercrap ones are 310nm....

transquip link

should be fine Adam - as long as you have the air pressure for it

there is a tool out there, but i cant find the name - its has a 3/4 inch fitting for a socket with a small arm attached to a swivelling long arm

you hit the long arm with it setup like an L so the down force from the hammer blow cracks the nut.

if i find it i'll post up

For flywheel bolts I've always just used a 1/2 inch breaking bar and socket...

How did you hold the crank still? With a rattle gun i can just ignore that issue. And its a good excuse for buying new toys!

Hey, you guys might be able to answer me.

Cylinder hones, whats better the flexible ones (with all the abrasive balls) or the ones with 3 straight stones.

Ive used the 3 stone ones before with pretty good success but never tried the flexi ones.

Cheers

How did you hold the crank still? With a rattle gun i can just ignore that issue. And its a good excuse for buying new toys!

You can get a tool that bolts onto two of the bell housing spots, and it locks into the flywheel.

I believe the Volkswagen one fits.

I also just had some piece of steel around that fitted the above job perfectly.

Hey, you guys might be able to answer me.

Cylinder hones, whats better the flexible ones (with all the abrasive balls) or the ones with 3 straight stones.

Ive used the 3 stone ones before with pretty good success but never tried the flexi ones.

Cheers

3 stone hone will take alot more of the bore out

ball hone is just to de-glaze the bore or to remove surface rust if oil ran away from one bit

should be fine Adam - as long as you have the air pressure for it

there is a tool out there, but i cant find the name - its has a 3/4 inch fitting for a socket with a small arm attached to a swivelling long arm

you hit the long arm with it setup like an L so the down force from the hammer blow cracks the nut.

if i find it i'll post up

You're talking about one of these; right? post-61153-0-84460800-1307628247_thumb.jpg Sidchrome Impact bar. Only ever seen 1/2" drive though.

Features

  • • Creates impact to shock frozen nuts loose
  • • 8 x torque multiplication with a single hammer blow
  • • No compressed air required
    I have one; Best. Tool. Ever. Well, except for ratcheting ring spanners...
    Link to sales; http://www2.blackwoo...04738&P=2028222

Edited by Daleo

Features

  • • Creates impact to shock frozen nuts loose
  • • 8 x torque multiplication with a single hammer blow
  • • No compressed air required
    I have one; Best. Tool. Ever. Well, except for ratcheting ring spanners...
    Link to sales; http://www2.blackwoo...04738&P=2028222

DO WANT! How much? I didn't see a price on the blackwoods link.

DO WANT! How much? I didn't see a price on the blackwoods link.

Sorry mate, missed the query...:blush: $165

Link; http://www.getprice....6--44917348.htm

You might do better, but at least an indication.

Cheers, Dale

Edited by Daleo
  • 3 weeks later...

Ill try and keep this thread alive!

Picked up this set to replace my lost 3/8" repco gear..

IMG_0199.jpg?t=1309686078

Love the deep sockets :) Got it off ebay for a decent price but one of the ratchets is faulty!!! would i be able to swap this over at bunnings? pain in the ass sending it back to the seller...

Also picked up a new tool bag the Veto pro pac xxl-f :) from http://www.thetoolbloke.com.au/

veto-pro-pac-xxl-f-closed.jpg

IMG_0237.jpg

Next on the list is some ratchet spanners! not sure if i should go the flex head or the standard reversible fixed type.

  • 1 month later...

post-74990-0-42970400-1309730666_thumb.jpg

~$30 of awesome

Tie-rod end/pit-man arm puller, long gone are the frustrating hours of hammering the crap out of, prying, heating, WD-40'ing etc. Put it on, wind in the bolt, CRACK, done!

Want!

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...