Jump to content
SAU Community

Recommended Posts

Ever wondering if your speedo is accurate?

So far Ive been in 2x Stagea's (mine and a mates) and both speedo's were out by 10%.

So for every 10km/h on the clock it was out by 1km/h...

Note: This was with FACTORY Spec Tyre Dimentions + Factory Alloys.

Ie: 10Km/h(clock) = 9km/h(Real Time) & 110km/h(clock) = 100km/h(Real Time)

I noticed when I used to hit Speed Cut at 180km/h.. Navman would be Register 170km/h.

Someone once told me that Nissan did this so you didnt speed? and its only till 100km/h(Real Time)

as very few free/highways exceed this speed.

Cheers, Aerron

Link to comment
https://www.sau.com.au/forums/topic/327028-speedo-calibration/
Share on other sites

  • Replies 50
  • Created
  • Last Reply

Top Posters In This Topic

Top Posters In This Topic

Posted Images

Most cars speedometers - not just Nissans - will err on the side of over-reading (reading higher than the road-speed).

From what I understand, speedometer accuracy is a tricky business for car manufacters. They need to allow for things like:

* Tyre wear

* Tyre temperature

* Variations in factory-released tyre rim sizes in a single model (where all models share the same speedometer and sensor)

As soon as you start introducing non-factory components like aftermarket rims & changes in the overall diameter of the wheel (different tyre profiles, widths, etc) you introduce even more variables that may affect your speedometer accuracy. The manufacturer will typically provide a tyre placard which lists acceptable tyre rim/tyre sizes for your car - it's up to the owner to ensure that they keep the rolling diameter as close to this as possible to try and avoid upsetting the speedometer accuracy. (Though there are state-by-state laws regarding how much the rolling diameter can be too).

There are regulations under the ADRs regarding speedometer accuracy. These have since changed in - I think - 2006 to be even more stringent, but for most of us it's still under the older rule that it must be accurate within +-10%. From what I recall, the new rules prevent any under-reading, and allow for over-reading of up to 4kph + 10%.

Testing against GPS, both of my cars over-read, but even at 100kph it's only 1-2kph out - so I don't stress too much.

Anyway, hope that helps :)

Most cars speedometers - not just Nissans - will err on the side of over-reading (reading higher than the road-speed).

From what I understand, speedometer accuracy is a tricky business for car manufacters. They need to allow for things like:

* Tyre wear

* Tyre temperature

* Variations in factory-released tyre rim sizes in a single model (where all models share the same speedometer and sensor)

As soon as you start introducing non-factory components like aftermarket rims & changes in the overall diameter of the wheel (different tyre profiles, widths, etc) you introduce even more variables that may affect your speedometer accuracy. The manufacturer will typically provide a tyre placard which lists acceptable tyre rim/tyre sizes for your car - it's up to the owner to ensure that they keep the rolling diameter as close to this as possible to try and avoid upsetting the speedometer accuracy. (Though there are state-by-state laws regarding how much the rolling diameter can be too).

There are regulations under the ADRs regarding speedometer accuracy. These have since changed in - I think - 2006 to be even more stringent, but for most of us it's still under the older rule that it must be accurate within +-10%. From what I recall, the new rules prevent any under-reading, and allow for over-reading of up to 4kph + 10%.

Testing against GPS, both of my cars over-read, but even at 100kph it's only 1-2kph out - so I don't stress too much.

Anyway, hope that helps :rofl:

I wasnt so much stressing, more so curious :)

You did bring up alot of good points...

My partner works for Toyota, she was telling me recently that all staff were warned that the new Tarago's speedo can be inaccurate by Approx 20km/h :) ... I was rather shocked.

Toyota... a leading manufacturer could be that far off. Fresh out of the box even?

But it is a Luck the Draw so 1-2% of the production could be wrong.

I bring this subject up as I went for a VERY EARLY Sunday Morning blat to stretch the Stag's legs out.

(Yes I know its dangerous to me and others etc... so smack me down if you will)

I was reading Navman's Speed as I did so, noticed that the Stags needle was above the Odometer(roughly 5 o'clock) and the Navman only said 190km/h... So I continued onto 205km/h.

I know using Nissan Consult you can re-calibrate a R33's Spedometer. Is it possible in the 34's/Stagea?

Cheers

Edited by JDM_Spirit

Mines out and over, 245/40R18 on 18x9.5' on RS4S (max std 215/50R17)

IE: needle - 110kmh pfc - 106kmh gps - 105kmh,

needle - 120kmh pfc - 114kmh gps - 113kmh

Power FC display is even different to needle but more accurate.

both of my stageas have over-read the speed. When the GPS reads 100km/h the speedo usually says about 108km/h.

Its a bit less than 10% but it means if I sit at 65km/h via the needle I'm actually doing about ~60km/h - most of the time i sit closer to 60...but the extra leeway has saved me from a fine more than once.

^^^^ This was on a private road... Right?
I should bloody well hope so!

:P ... Well.... technically I drove on a piece of My Road as part of my Tax and Rego paid for it.

Im running 17's with 500km old 235/45R17's.

GPS : 110km/h Needle = 117km/h ish

i would sit at

50 speedo , 45 real time.

90 speedo, 80 real time.

116 speedo , 100 real time.

so i couldnt work it out haha, sold the car the new owner put 20's on it and said its only like 3ks off now all round, according to his GPS

Pretty much all cars are set up to be out. Brand new camry's have the correct reading at the ECU but then change it for the speedo to be 10% out, don't ask me why, they just do. but it explains why camry drivers always seem to go so slow.

Mines out and over, 245/40R18 on 18x9.5' on RS4S (max std 215/50R17)

IE: needle - 110kmh pfc - 106kmh gps - 105kmh,

needle - 120kmh pfc - 114kmh gps - 113kmh

Power FC display is even different to needle but more accurate.

That's probably due to the extra stretch your tyres have made to go over the 9.5"rims, as I have exactly the same size tyres on my car, but on 18x8" rims, and it's only aout 1km/h out.

My PowerFC is way off both the speedo and actual real-time speed my car is travelling at.

with my ecutalk and gps i get 3 different speeds

the ecutalk over reads the ground speed and the dash shows more than that again

and as somone said, its pretty accurate up to about 80 (both dash and ecu are in sync) then they start to separate

anyone used the jaycar speed corrector kit?

8-10% over-read. Means it has more kms on the clock than it has done!

Mines out about 7%. Trip to work in my Magna is 114km and the Stagea is 122km. 18" Advant T7s with 225/45 with rolling diameter of 2072.5mm whereas standard is 215/55x17" so rolling diameter is 2099.5mm. So smaller by 27mm hence more km on the odometer.

Mines out about 7%. Trip to work in my Magna is 114km and the Stagea is 122km. 18" Advant T7s with 225/45 with rolling diameter of 2072.5mm whereas standard is 215/55x17"

I run 245/45/18 and my error is approx 3% against GPS, which I'm quite happy with. Where in the mountains are you Rosella? I'm at Faulconbridge, I'll have to keep my eyes peeled.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...