Jump to content
SAU Community

Recommended Posts

Further to my weight reduction game,,,Fatz gave me this Stagea pedal as mine was slightly burnt during the cage installation. It might be only about 300grams but it cost nothing.

post-29-0-52122400-1431844066_thumb.jpg post-29-0-70411700-1431844102_thumb.jpg

I've finished making version 2 of my air box. This time I've used some off cuts front my front splitter material and done away with the heat/sound insulation. I forgot to take a weight pic of the side half but it's the same weight as the top,,, So 1.2KG removed.

post-29-0-96982100-1431845155_thumb.jpg post-29-0-33905500-1431845195_thumb.jpg

post-29-0-00444100-1431845322_thumb.jpg post-29-0-72826500-1431845579_thumb.jpg

post-29-0-81275600-1431845597_thumb.jpg

Cheers

Neil.

  • Like 2

So onto the next diet job. I was sort of hoping the I could cut this bump out and sit my battery down but I should know better.

post-29-0-18043200-1431849354_thumb.jpg

I knew something would be under there but was hoping I could cut the lump out flush and have the battery looking like this.

post-29-0-82774600-1431849531_thumb.jpg post-29-0-69160700-1431849631_thumb.jpg

But not to be,,,Nissan had decided that a breather should be in the way,,,

post-29-0-46621700-1431849691_thumb.jpg

So back to plan "B" a 120 bucks and a up-right hold down bracket.

Cheers

Neil.

Play "B" has worked out a treat,,,battery and rear relay/fuse box is in and looking good.I do need to buy a battery positive terminal cover that fits properly though.

post-29-0-18127700-1432466805_thumb.jpg

Duncan and I did lots of good easy jobs today :-

Rolled the front guards and flared them at the same time so I don't have any clearance problems with the bigger slicks.

Swapped the front discs left to right,,,I run them wrong side round on the shorter climbs to stop the vanes from cooling the discs,,,but this next one is longer with 7 braking points so getting less heat in them is essential. Changed pads as well to softer ones.

The Patrol got a new volt meter and Duncan fixed my rear camera so we should be able to see out the back now.

Wheel alignment and corner weighting next weekend,,,with the normal last weekend jobs to be done as well.

I even spent the late arvo cutting the grass.

Cheers

Neil.

  • Like 2

We are staying at this place mate,,,

http://www.jacarandamotorlodge.com.au/

Here's the address of the track

Mountain View Motor Sports Complex NSW

262 Clarence Way, Mountain View

Cheers

Neil.

What is the beastie weighing now, you seem to have pulled some fat out of it.

Can you "depower" the steering rack? I was bored and did it to the 5, the steering is actually better I find now, I did cut out the internal piston to negate the internal pressure, with brackets, pumps and fluids I lost about 10kg (ish).

Guess the weight?????

My guess is 1432.6 kg with half a tank of fuel and a driver half full of beer.

What is the beastie weighing now, you seem to have pulled some fat out of it.

Can you "depower" the steering rack? I was bored and did it to the 5, the steering is actually better I find now, I did cut out the internal piston to negate the internal pressure, with brackets, pumps and fluids I lost about 10kg (ish).

Guess the weight?????

My guess is 1432.6 kg with half a tank of fuel and a driver half full of beer.

Hey Mark,,,how they hangin mate?.

I will find out tomorrow what Cheryl weighs. I've just finished filling her up with 40 litres of fuel for tomorrow so I'll get a wet reading.

Depower the steering,,, While that would save way more than 10 kilo's on a gtst,,,I'd have to go to the gym to steer the bloody thing. I did ages ago try steering her without the belt on and man it was hard going. I seem to remember Duncan struggled with steering his r32 without a belt on the track!!!.

Guessing the weight,,,shit it better not be anywhere near your prediction,,,1375 is standard so anything under 1300 would put a smile on my face tiger.

Cheers

Neil.

Neil, the problem with the PS when the belt is removed is that you are trying to pump hydraulic fluid through the system by arm power, when you fully depower a rack all fluid is removed and a grinder is taken to the internal piston which is pressed on inside the rack, this eliminates the pressure you have when the belt is removed/fails/falls off, the removal of the piston removes the internal air pressure which means you can bung the old PS fittings.

If you can find a spare rack, strip it down and look for the piston on the steering rod inside the rack.

The steering will be slightly heavier when you are moving slow but once you are moving it is easy as.

I was going to get a manual rack for mine but found that if fully depowered the rack I would have better ratios (less turns lock to lock), Ive driven a 5 with a manual rack and I prefer the depowered one.

Took me about 6 beers from full PS to fully depowered.

GOOGLE "De-powering a Miata power steering", I assume that all PS racks would be basically the same.

Rock and Roll

You two are funny f**cks. Friday night beers must have been great. Me I don't drink anymore,,,.

Mark, I thought your idea of "de-powering" my steering might have had some merit so I did some asking and searching. Done properly I'd recon I could lose about 15 kilo's but as I said above I do need to steer the car at low speeds as well. If I had a little girls car like yours powered by a lawn mower engine I would jump at it in a flash.

Cheers

Neil.

LOL, fair call.

Edit: I wish I had the power of a lawn mower.

Edit, Edit: I'm on the Scotch tonight, winning, the brilliant ideas will be coming fast and furious in a few hours time.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
    • I'd say it's a fair bet that the feed and return fluid lines will be in different enough spots that you would need to come up with a way to cut the originals short and adapt with new hard line adaption or braided teflon hoses or somesuch. But really, you have the car, you have the photos of the DMAX rack - you should be able to go out there and see for yourself whether they're in the same or different spots.
    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
×
×
  • Create New...