Meathead Posted February 10, 2016 Share Posted February 10, 2016 yes that is correct @harrisracing -- cut the end off and its a standard vband. the same as any Cummins/Holset turbo and many other BW or MHI turbos. There are cast 90 degree vbands available for this application but you could also just but a vband and weld the intercooler pipe to it Hey Geoff, do you have these bends for sale? did not notice them on you website. Link to comment https://www.sau.com.au/forums/topic/341890-closed-borg-warner-efr-series-turbos/page/117/#findComment-7681415 Share on other sites More sharing options...
JustinP Posted February 14, 2016 Share Posted February 14, 2016 (edited) I might be interested in one of those vband 90 degree bends too. Or even just the vband to suit the outlet, I couldn't find them on the Full Race site. Actually I also need an exhaust vband flange and clamp to suit an EFR8374 0.92 IWG turbo, an EFR boost solenoid pigtail and an internal wastegate canister heat shield (thats compatible with the single port Turbosmart actuators). Maybe you could do a package for us in Australia? Edited February 14, 2016 by JustinP Link to comment https://www.sau.com.au/forums/topic/341890-closed-borg-warner-efr-series-turbos/page/117/#findComment-7683328 Share on other sites More sharing options...
Full-Race Geoff Posted February 14, 2016 Share Posted February 14, 2016 Sorry, we do not make them, and havent offered them for sale. however i will look into it next week 1 Link to comment https://www.sau.com.au/forums/topic/341890-closed-borg-warner-efr-series-turbos/page/117/#findComment-7683518 Share on other sites More sharing options...
[200] Posted February 27, 2016 Share Posted February 27, 2016 Have you received any info regarding the new s400-sxe range ? I noticed a SEMA 2015 video where a couple of reps from Borg Warner were talking about them. One in particular was an 88mm 10 blade compressor wheel with 1.15 a/r t6 exhaust housing. Any indication on what will be available for a t4 exhaust housing? Seems to be a bit of limited information so far, but some have been listed on Jegs too. I was about to buy a s400sx3 until I saw the video - might as well hold out a little longer. Thanks Link to comment https://www.sau.com.au/forums/topic/341890-closed-borg-warner-efr-series-turbos/page/117/#findComment-7689617 Share on other sites More sharing options...
2pee Posted March 1, 2016 Share Posted March 1, 2016 Assume the 7163 aluminium chra is the same as the old 6758 indy car one...excluding the wheel diameters. Is there any possibility of BW supplying or producing them again? Link to comment https://www.sau.com.au/forums/topic/341890-closed-borg-warner-efr-series-turbos/page/117/#findComment-7691022 Share on other sites More sharing options...
Full-Race Geoff Posted March 3, 2016 Share Posted March 3, 2016 Have you received any info regarding the new s400-sxe range ? I noticed a SEMA 2015 video where a couple of reps from Borg Warner were talking about them. One in particular was an 88mm 10 blade compressor wheel with 1.15 a/r t6 exhaust housing. Any indication on what will be available for a t4 exhaust housing? Seems to be a bit of limited information so far, but some have been listed on Jegs too. I was about to buy a s400sx3 until I saw the video - might as well hold out a little longer. we have the all new 10 blade 72mm SXE in stock now. 110lb/min from a 72mm inducer is very impressive! the 88mm is approx 4-6 weeks out the last i heard. if youd like to email me at geoff[at]full-race[dot]com with the exact spec you are interested in, I will get you an update asap. pics of the 72mm from our instagram feed this week: Assume the 7163 aluminium chra is the same as the old 6758 indy car one...excluding the wheel diameters. Is there any possibility of BW supplying or producing them again? sorry i do not understand your question? Link to comment https://www.sau.com.au/forums/topic/341890-closed-borg-warner-efr-series-turbos/page/117/#findComment-7691964 Share on other sites More sharing options...
[200] Posted March 3, 2016 Share Posted March 3, 2016 Thanks. I was hoping they might have something in 76mm + compressor wheel / 87mm turbine. t6 is too big for my engine bay. Hopefully they will redo the 80mm or 82mm billet in the new compressor wheel configuration. I'll keep an eye out and send you an email when more info comes available. Link to comment https://www.sau.com.au/forums/topic/341890-closed-borg-warner-efr-series-turbos/page/117/#findComment-7692025 Share on other sites More sharing options...
Meathead Posted April 25, 2016 Share Posted April 25, 2016 Sorry, we do not make them, and havent offered them for sale. however i will look into it next week Managed to find these from Boostresource, picked one up the other day. 1 Link to comment https://www.sau.com.au/forums/topic/341890-closed-borg-warner-efr-series-turbos/page/117/#findComment-7717915 Share on other sites More sharing options...
HarrisRacing Posted April 26, 2016 Share Posted April 26, 2016 Managed to find these from Boostresource, picked one up the other day. How much was it? Link to comment https://www.sau.com.au/forums/topic/341890-closed-borg-warner-efr-series-turbos/page/117/#findComment-7718514 Share on other sites More sharing options...
Meathead Posted April 27, 2016 Share Posted April 27, 2016 How much was it? $75 it's not listed, but they sell separately, comes as part of a kit. Send these guys an email if you want one [email protected] Link to comment https://www.sau.com.au/forums/topic/341890-closed-borg-warner-efr-series-turbos/page/117/#findComment-7718881 Share on other sites More sharing options...
Piggaz Posted May 16, 2016 Share Posted May 16, 2016 What size oil drains are you guys running? Link to comment https://www.sau.com.au/forums/topic/341890-closed-borg-warner-efr-series-turbos/page/117/#findComment-7728217 Share on other sites More sharing options...
Meathead Posted May 16, 2016 Share Posted May 16, 2016 What size oil drains are you guys running? AN10 5/8" id to the front drain. Link to comment https://www.sau.com.au/forums/topic/341890-closed-borg-warner-efr-series-turbos/page/117/#findComment-7728224 Share on other sites More sharing options...
Piggaz Posted May 16, 2016 Share Posted May 16, 2016 Have you started the car yet? Link to comment https://www.sau.com.au/forums/topic/341890-closed-borg-warner-efr-series-turbos/page/117/#findComment-7728239 Share on other sites More sharing options...
HarrisRacing Posted May 16, 2016 Share Posted May 16, 2016 AN10 5/8" id to the front drain. -10 AN to the REAR drain. Link to comment https://www.sau.com.au/forums/topic/341890-closed-borg-warner-efr-series-turbos/page/117/#findComment-7728253 Share on other sites More sharing options...
HarrisRacing Posted May 16, 2016 Share Posted May 16, 2016 Just got my car very roughly tuned in enough to make a decent 10 psi pull and I AM LOVING THIS TURBO! Sounds frigging awesome, responds very well, seems to spool strong at around 3700-4k rpms (I'll log it soon). And I assure you I have a little lean spot on the bottom and I haven't touched timing yet, so I'm sure it will get better! Quick little video. Link to comment https://www.sau.com.au/forums/topic/341890-closed-borg-warner-efr-series-turbos/page/117/#findComment-7728255 Share on other sites More sharing options...
Meathead Posted May 16, 2016 Share Posted May 16, 2016 Have you started the car yet? if you mean me, not yet probably another month, still at work. -10 AN to the REAR drain. I'm using a Fullrace IWG manifold so the drain has a easy run between 1&2 runners That turbo sounds sweet! looking forward to seeing it tuned ...you must have worked an all nighter to get that engine back together! Good job! Link to comment https://www.sau.com.au/forums/topic/341890-closed-borg-warner-efr-series-turbos/page/117/#findComment-7728261 Share on other sites More sharing options...
HarrisRacing Posted May 17, 2016 Share Posted May 17, 2016 BW 8374 EFR .92 iwg on 93 octane pump on Tomei poncam A cams, ported head, SS valves, hypertune V2 manifold, 8.5:1 CR, stock bores, 79mm stroker BC crank, 6 boost divided IWG manifold, Day 2 of tune...still not 100% by any means, cams not set at all (straight up zero on both)... 3rd gear pull from 2800 rpms: 5.0 psi boost at 3,077 rpms. 9.0 psi boost at 3,555 rpms per Haltech log I just pulled. I'm sure there is more room here for better spool. I'm only set to 10 psi boost in haltech right now for break in and simple map tuning. I would tell you where it goes to 10 but clearly ecu is sending signal and causing slow rise around 9.5 psi. Just thought I would share. stock intercooler for now Link to comment https://www.sau.com.au/forums/topic/341890-closed-borg-warner-efr-series-turbos/page/117/#findComment-7728405 Share on other sites More sharing options...
BoostdR Posted May 19, 2016 Share Posted May 19, 2016 Response is effected dramatically by wastegate tension I have found. 1 Link to comment https://www.sau.com.au/forums/topic/341890-closed-borg-warner-efr-series-turbos/page/117/#findComment-7729454 Share on other sites More sharing options...
MaximuSmurf Posted May 19, 2016 Share Posted May 19, 2016 Response is effected dramatically by wastegate tension I have found. You're running internal gate? Do you mean whether you get the soft, medium or hard spring in the internal actuator? 1 Link to comment https://www.sau.com.au/forums/topic/341890-closed-borg-warner-efr-series-turbos/page/117/#findComment-7729500 Share on other sites More sharing options...
Dose Pipe Sutututu Posted May 19, 2016 Share Posted May 19, 2016 try dropping some timing as you come on boost, helps get the EGTs a little hotter which helps gets the turbo to boogie Link to comment https://www.sau.com.au/forums/topic/341890-closed-borg-warner-efr-series-turbos/page/117/#findComment-7729572 Share on other sites More sharing options...
Recommended Posts