Jump to content
SAU Community

Recommended Posts

On ‎1‎/‎07‎/‎2016 at 5:20 AM, VFRegal said:

Tom is yours a T4 TS IWG ?
Did you run the stock actuator and or have any issues with boost control ?

 

For anyone interested, here is my 7670 dyno graph.

 

Car is an Evo V. As you can see, it's fairly responsive.

 

Not pushing it at all on 98, only 20 psi.

 

attachicon.gifEvo_98.jpg

 

 

Hey man, it's T4 twin external gates. While the plumbing is a nightmare, I didn't want to have to deal with boost control issues

6 hours ago, Tom Tucker said:

Hey man, it's T4 twin external gates. While the plumbing is a nightmare, I didn't want to have to deal with boost control issues

Cheers. Like your S15 was. I've got dramas with my 7163, unsure if tuner or setup so far. Tempted to convert to EWG.

10 hours ago, VFRegal said:

Cheers. Like your S15 was. I've got dramas with my 7163, unsure if tuner or setup so far. Tempted to convert to EWG.

If you're on a SR20.. you will find the low timing dip when torque ramps up will cause the turbo to over boost a bit.. a touch hard to iron out.. unless you're on E85 and can dial in more timing.. Either that control your boost solenoid by DC vs RPM.

3 hours ago, Dose Pipe Sutututu said:

If you're on a SR20.. you will find the low timing dip when torque ramps up will cause the turbo to over boost a bit.. a touch hard to iron out.. unless you're on E85 and can dial in more timing.. Either that control your boost solenoid by DC vs RPM.

SR20, E85. Boost just dropping off like mad. I need to go through the setup a bit better as current tuner doesn't seem interested in trying to find the issue and is blaming the turbo and being IWG. Boost control is by rpm on avc-r with 4 port mac valve dual port turbosmart actuator.

Awesome turbo even with the boost dropping. Just pulls like mad.

40 minutes ago, VFRegal said:

SR20, E85. Boost just dropping off like mad. I need to go through the setup a bit better as current tuner doesn't seem interested in trying to find the issue and is blaming the turbo and being IWG. Boost control is by rpm on avc-r with 4 port mac valve dual port turbosmart actuator.

Awesome turbo even with the boost dropping. Just pulls like mad.

In the AVC-R, when you're in the Setting Menu, hit next next.. it allows you to fine tune duty cycle by RPM (which is defined in the NE Menu). See where boost is bleeding off and add DC to those RPM points defined by the NE Points.

 

Who's tuning your car?

1 hour ago, VFRegal said:

SR20, E85. Boost just dropping off like mad. I need to go through the setup a bit better as current tuner doesn't seem interested in trying to find the issue and is blaming the turbo and being IWG. Boost control is by rpm on avc-r with 4 port mac valve dual port turbosmart actuator.

Awesome turbo even with the boost dropping. Just pulls like mad.

SUPER interested to hear about these results. Is it a stock / forged SR20? Most people seem to be running these on SR22's or VET's. Hard to find much info on a 'plain old' SR20.

So you're running EFR 7163 on SR20 with T4 TS internal gate? Low mount Hypertune manifold? High mount Fullrace manifold? This is the exact combo I was looking at. NOTHING wrong with my current GTX2863R setup (except it doesn't hold boost very well). Looking for an excuse to go to BW town. Was looking at 6758 for crazy response setup, but from what I'm reading there will be minimal loss in response going to 7163, and much nicer fat top end.

Got a dyno chart of the setup?

FYI I'm running forged engine and e85 setup (although currently maxxing my 950cc injectors). Greddy Eboost Profec II Spec B (who comes up with these freakin names). Z32 AFM, Nistune w/flex.

use a turbosmart dual port actuator.. I tuned a SR20 with a GTX2867 using that actuator and the boost was pretty flat.. not ruler flat as an EWG but flat enough :)

Just fuel system couldn't keep up, ripping out the junk DW300 and replacing it with a Walbro 450L

21 minutes ago, Dose Pipe Sutututu said:

use a turbosmart dual port actuator.. I tuned a SR20 with a GTX2867 using that actuator and the boost was pretty flat.. not ruler flat as an EWG but flat enough :)

Just fuel system couldn't keep up, ripping out the junk DW300 and replacing it with a Walbro 450L

Interesting. I'm running aftermarket Kinugawa actuator on mine with 19psi spring in it. Currently hits about 24psi... then tapers down to ~19psi.Would love to be able to hold the ~24psi all the way, would net a little more top end and pull a bit harder once up and going... that's about the limit though. 0.64 rear housing so it chokes a bit with anymore boost.

PS. Yeah I'm running the Walbro 450lph fuel pump too, hard wired... no issues thus far.

 

Chequered - Power- 271 - Fixed boost leak.jpg

Chequered - Boost - 271 - Fixed boost leak.jpg

try turning your gain down so the EBC is more lazy and increase your SET to higher

anyhow, these twin ports are great for controlling boost.. just remember to set your EBC to external waste gate mode to use the twin port

http://www.turbosmartdirect.com/Product-Categories/Universal-Fit-Internal-Wastegate-Actuators/IWG75-Twin-Port-Universal-150mm-14-PSI.html

2 hours ago, VFRegal said:

SR20, E85. Boost just dropping off like mad. I need to go through the setup a bit better as current tuner doesn't seem interested in trying to find the issue and is blaming the turbo and being IWG. Boost control is by rpm on avc-r with 4 port mac valve dual port turbosmart actuator.

Awesome turbo even with the boost dropping. Just pulls like mad.

Wouldn't a restriction from IWG lead to boost creep rather than a drop?

The other possibility is compressor running out of puff but 7163 can flow quite a lot. Couple of guys on nissansilvia running it, one on a slightly higher comp VET setup, which would be more prone to boost drop in that situation - think that's bradsm87. Pretty sure he's IWG but cant remember for sure. Also nicknack had one IIRC.

Edited by Skepticism

Stock sr20 260 procams. nistune E85, blow through Z32. Was running hks evcs switched avc-r for boost control by rpm as recommend by tuner.
Fullrace top mount TS 7163 and dump. I think it's either a leak or wastegate setup so need to find dyno for hire or somewhere a bit more receptive to testing / debugging.

There's a bit of info over at NRR and on NS in the efr threads.

Finally finished fitting an EFR 8374iwg  on a 2.8 and must say it is a step up from the 5s in every way.

Definitely recommend it.

 

P7070013.thumb.JPG.db6eca751148cfa5d5ff0d81f044ed75.JPG

Welcome to the club!

I would really like to see how mine compares boost threshold etc on pumpgas if you can get some data. Thanks!

 

26 minutes ago, HarrisRacing said:

Welcome to the club!

I would really like to see how mine compares boost threshold etc on pumpgas if you can get some data. Thanks!

have you pulled out timing yet? it will seriously wake up your turbo

Mine has begun, should be getting tuned in about 3 weeks if all goes to plan

Stock rb26

T4 twin scroll manifold

EFR 8374 twin scroll 1.04

External gate

Custom 3.5" exhaust

264 cams, springs/retainers, studs and metal head gasket

Haltech

E85

I doubt I'll be able to get its maximum potential given the stock bottom end but we should see 500kw and 30psi around 4100rpm

 

2016-07-05_20.59.45.jpg

11 hours ago, Dose Pipe Sutututu said:

 

have you pulled out timing yet? it will seriously wake up your turbo

Adding fuel DEFINITELY helped...I had a lean spot. I've been playing with cams and all but vacation took some days out of my tuning schedule :) .

Advancing cams 2 deg in and 2 deg ex didn't really help. I think the Tomei's like 0 and 0 to be honest. It was my best overall powerband.

I'll pull timing on boost onset for you today and get back to back logs at same temps, etc.

 

Also I want to note that the car is extremely responsive and drivable. in 3rd it's full boost almost exactly at 4k and I'm very happy with that. I have compared my powerband to lots of others and it's extremely acceptable so far. Top end is ridiculous.

 

 

2 hours ago, usmair said:

Mine has begun, should be getting tuned in about 3 weeks if all goes to plan

Stock rb26

T4 twin scroll manifold

EFR 8374 twin scroll 1.04

External gate

Custom 3.5" exhaust

264 cams, springs/retainers, studs and metal head gasket

Haltech

E85

I doubt I'll be able to get its maximum potential given the stock bottom end but we should see 500kw and 30psi around 4100rpm

 

2016-07-05_20.59.45.jpg

Should be awesome!!!

I'll be moving to E85 in the next couple of months as well. Done with this pumpgas! I am just leaving too much power on the table.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Have a vb in honour of the car comming back
    • It was a great, but typical track day, and some VB was ingested at the night time debrief 🤪
    • And so, to round this out, I couldn't be happier to confirm @MBS206 has decided to buy the car. He drove down from sunny QLD with a trailer last week and it is off to its new home today. I'll let Matt confirm on next steps but I understand broadly that the plan is to leave it pretty much as is, and just get some quality wheel time with a nicely balanced car that is pretty much track ready. There are a few a jobs still to be done first but nothing too major and I think its a very smart buy Dinner last night at the Paragon with a round of VBs (mostly) for Neil
    • Well, 50 pages and the end of a chapter for this car. We took it out for a shakedown at Wakie yesterday, and everything went well. There were a couple of niggles: - Oil cooler fitting leak - tightened, cleaned, stopped leaking - Radiator cap overflow fitting was leaking....Mark called it, the overflow fitting was threaded in and not tight....tightened, tested and held pressure - Small oil leak at the rear of the block, probably the turbo oil feed - too hot to get at it comfortably but probably just needs to be nipped up - leak at the driver's side rear brake line where it meets the hardline. Fitting wasn't loose, so Matt backed it off and back on, no further leaks - there's also a leak somewhere on the top of the fuel tank, maybe that cross over fuel line - that was has been left to fix when its on a hoist Otherwise than those niggles the car went great, turned great and stopped great so it was a very successful day out. I'm always really nervous when a car first hits the track after a long break, especially with a brand new engine as well but it was great. VID-20251011-WA0007.mp4  Big thanks to @The Bogan who dropped by and helped out, @MBS206 and my nephew Lachlan the apprentice.  Neil's wife Mel also surprised the hell out of all of us by dropping by; she's up in Tamworth these days but was travelling to Melbourne so had plausible deniability for turning up at the garage, it was great to see her but also obviously a bit sad all round.
    • Skyline R33 Series 2 sedan tail lights in excellent condition. These are becoming harder to find, especially in this state.    BOTH SETS ARE IN FANTASTIC CONDITION (REFER TO PHOTOS)    ✅ No broken covers or cracks ✅ Lenses are in flawless condition ✅ All rear mounting lugs intact ✅ Comes complete as pictured ✅ Perfect for restoration, replacement, or upgrade   These lights are ready to go, no surprises just quality OEM parts.   These are definitely one of the better sets we have seen in a while. With minimal wear and tear they will come as you see. Bear in mind they are not brand new they are almost 30 years old now. To find them in this condition isn’t easy they can only be obtained on the second hand market.   Australia Wide Postage Available At Buyers Expense. Silver Set:$850 Grey Set:$850 PM Me for purchase or any other questions  IMG_2166.dng IMG_2165.dng IMG_2172.dng IMG_2173.dng IMG_2174.dng IMG_2179.dng IMG_2180.dng IMG_2260.dng IMG_2258.dng IMG_2259.dng IMG_2261.dng IMG_2266.dng IMG_2273.dng IMG_2274.dng IMG_2276.dng
×
×
  • Create New...