Jump to content
SAU Community

Recommended Posts

Well, after owning the stag for just over 4 years now and driving it pretty much as it came. I have almost completed my 1st couple of mods/additions.

I purchased a Turbo Tech MBC off ebay & after trolling thru a stack of threads I managed to get it fitted the way it should. I also bought a boost gauge & air/fuel gauge from one of the skyline boys, purchase a few bits & pieces from my local auto shop & fitted them below the radio in my centre console. StagMBC_2.jpgStagMBC_1.jpgStaggauges_1.jpg

Any suggestions on what I should put in the 3rd gauge slot???

Just fitted V spec Brembo all round , crap !!!! , is there a certain bleeding procedure ? , whiteline Anti roll bars front and rear , Awesome ! , front adjustable upper arm bushes , camber better ! ,

Well, after owning the stag for just over 4 years now and driving it pretty much as it came. I have almost completed my 1st couple of mods/additions.

I purchased a Turbo Tech MBC off ebay & after trolling thru a stack of threads I managed to get it fitted the way it should. I also bought a boost gauge & air/fuel gauge from one of the skyline boys, purchase a few bits & pieces from my local auto shop & fitted them below the radio in my centre console.

Any suggestions on what I should put in the 3rd gauge slot???

oil pressure

Just fitted V spec Brembo all round , crap !!!! , is there a certain bleeding procedure ? , whiteline Anti roll bars front and rear , Awesome ! , front adjustable upper arm bushes , camber better ! ,

unplug the abs

bleed the rears, furthest from brake master (bmc)

bleed fronts (both sides of each calliper)

plug abs back in

Looks sweet once it's done eh?

Yep. I ended up putting on the darkest legal (30% i think?) as I got pulled over earlier that week and was told my rear windows were illegal. (factory stained glass from nissan) Haha.

Yep. I ended up putting on the darkest legal (30% i think?) as I got pulled over earlier that week and was told my rear windows were illegal. (factory stained glass from nissan) Haha.

^^ police are becoming stupider by the minute.

Yep. I ended up putting on the darkest legal (30% i think?) as I got pulled over earlier that week and was told my rear windows were illegal. (factory stained glass from nissan) Haha.

I had mine done 20%whistling.gifthey're almost exactly the same as the back. If it didn't look so cool, it'd be a pain in the arse...

I figure if I ever get pulled over I'm going with "it's all factory tint" If that doesn't fly, I'll just strip it , inspection, re tint. Mine only cost $100 for the pair.

I got me an oil pressure gauge, only thing is its too big for the slot. Was thinking of mounting it on the A pillar at a later date. Any other suggestions......maybe voltmeter?

BTW............forgot to mention that I made the plate for the gauges to sit in, dead easy.

I got me an oil pressure gauge, only thing is its too big for the slot. Was thinking of mounting it on the A pillar at a later date. Any other suggestions......maybe voltmeter?

BTW............forgot to mention that I made the plate for the gauges to sit in, dead easy.

IMO if you are going to run multiple gauges, the most important ones will be boost, oil pressure, oil temp and water temp.

IMO if you are going to run multiple gauges, the most important ones will be boost, oil pressure, oil temp and water temp.

Thanks, probably put water temp in the open slot in centre console. The oil pressure gauge is too big to mount under radio, so I'll look at making dual A pillar mount out of fibre glass for oil pressure & oil temp.

Just bought the 'power duct' through Nissan. Looking forward to saving that amount of money over the next 8years 5 months (HAHahahha) in fuel economy from sucking in hot air from the engine.... :rolleyes:

looking at connecting the fuel/air gauge 2d. pwr connected, just need to run sensor wire to the heated O2 senser on the ECU (pin 50) if I'm not mistaken.

Waste of time, unless you get a wideband sensor.

Oil pressure, oil temp, exhaust temp, accurate water temp and wideband are all critical if you are tuning imo.

Waste of time, unless you get a wideband sensor.

Oil pressure, oil temp, exhaust temp, accurate water temp and wideband are all critical if you are tuning imo.

OK then how fo you know if its wide band??? or not. The one I got is Autometer Pro Comp Ultra Lite (refer above pic). Shows - lean, stoich & rich.

A wideband wont run off the ecu, it requires a wideband o2 sensor to be placed in the dump. It will give you an actual value instead of just rich/lean.

This is the one I have...

http://www.innovatemotorsports.com/products/lc1.php

A wideband wont run off the ecu, it requires a wideband o2 sensor to be placed in the dump. It will give you an actual value instead of just rich/lean.

This is the one I have...

http://www.innovatemotorsports.com/products/lc1.php

SHWEEEEEEET, something to save for asside from the home loan :D Thanks for the info, i also had a quick look at the new autometer clip for their wideband sensor/gauge.

Anyways, gonna finish wiring this up so my acr is ready for the trip to Dubbo 2m

got my intercooler today

ITS THE WRONG FKING ONE

sigh.. now have to way another 30 years for it to get here... and the fact that this "flood" has nothing to do with WA or where i am ordering my cooler from, it will still take bloody ages... so angry

well today i got the dump exhaust off..to fix the exhaust gasket leak.exhaust.. turns out there was maybe 1mm of the flange that WASNT leaking. When I pulled it off to fix it, it looks like the exhaust shop that did the exhaust did a dodgy, and shrunk the 3" to about 2.5" and put the stock flange back on (never taking it there again). Scotty the f**kn legend cut some of the exhaust off put it back to 3" with a new flange.. fixed.

Ok so made up a new gasket from Gasket material, with some gasket/exhaust seal. n put it back together..

it set.

Started the car.. i'de safely say about 50% of the turbo whine went away...sounds normal now..

still gonna take it to the turbo shop on monday to let him have a listen first..

once this all finished. i made some great souvlaki's and now im full and scotts so full he cant breathe!. goodnight Stagea owners.!

Edited by AaronNM35

that turbo whine you were hearing is awesome. LOVE the sound of the turbine when you have an exhaust leak :)

my bosses car has a dump straight to the ground from the turbo, i love driving it just to hear that sound. pity its attached to a mazda6 MPS

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...