Jump to content
SAU Community

Recommended Posts

hahah yeah ill want that too

with my new gearbox

well for $500.00 for the best shift kit i can get in mine. im happy.

that way if the box eventually gives up, i send it to him he rebuilds/upgrades the box for $2000....im happy with that

especially if Cihan's got something in mind for Trans ECU mapping like ironpaw said..

yeh. although my plugs in the car were pretty new, they were changed on complianced which im told is rare..

Damn. My compliance shop didn't even change the bloody oil. :rant: Stuff that came out was fairly black goddamit.

Lucky for me I changed it /trans oil/oil filter/plugs/air filter/and drained the rad water, and filled it up with the real stuff..... :rolleyes:

Damn. My compliance shop didn't even change the bloody oil. :rant:

lol they changed oil belts plugs power steering brake fluid.. pretty much everything except the transmission oil.

Im kinda glad they didnt change the trans because if they put the wrong oil in i may well be f**ked!

Edited by AaronNM35

neither did mine!!

removed all the good stuff though

i spoke to them prior to compliance and said i'd much rather a way you get around keeping all the goodies..

especially the remote start..

why cant they get rid of HICAS on compliance lol

Just some quick notes on the fitment of the 'power duct' to my NM35.

1. It makes more of a turbo induction noise on boost which I like. Keeps everyone guessing

2. Following a truck with hay bales on the drive over to S.A. means your air filter gets straw in it

3. Easier to see how dirty the filter is!

4. Economy I would hazard a guess is slightly better. I'm getting 550 to a tank of around 60-65L driving in peak hour.

Also, the Tanabe's coil overs are going well. Still wallowing a little (shock damper rate is lower than the springs require I would assume). Corners like it's on rails! Quite neutral with some understeer with light throttle.

Anyone know if the Autech Axis model has aftermarket sway bars? Me thinks so.

Just some quick notes on the fitment of the 'power duct' to my NM35.

1. It makes more of a turbo induction noise on boost which I like. Keeps everyone guessing

2. Following a truck with hay bales on the drive over to S.A. means your air filter gets straw in it

3. Easier to see how dirty the filter is!

4. Economy I would hazard a guess is slightly better. I'm getting 550 to a tank of around 60-65L driving in peak hour.

Also, the Tanabe's coil overs are going well. Still wallowing a little (shock damper rate is lower than the springs require I would assume). Corners like it's on rails! Quite neutral with some understeer with light throttle.

Anyone know if the Autech Axis model has aftermarket sway bars? Me thinks so.

i stole mine off my sisters v35. good thing i did too.. she wrote the bugger off!

Ok, better say what I have done somewhat lately - Tiptronic was reversed, to stop me changing down gears...

GB sway bars I put on last weekend, and Lowered Eibach springs went on earlier this week- waitin on 19" Rims, lowered ,the 17 " stockies look.... ridiculous! Car handles Amazingly for simple upgrades, much more faith in it.

R32 GTR brakes are waiting for the new wheels to come along, so I can stop properly :thumbsup:

Picked up a Z33 midpipe today from Northshore Prestige (thanks Guys). Thats an upgrade to the massive/quiet centre muff that on there. Apparently just got to get it extended 6 inches...

Ok, better say what I have done somewhat lately - Tiptronic was reversed, to stop me changing down gears...

GB sway bars I put on last weekend, and Lowered Eibach springs went on earlier this week- waitin on 19" Rims, lowered ,the 17 " stockies look.... ridiculous! Car handles Amazingly for simple upgrades, much more faith in it.

R32 GTR brakes are waiting for the new wheels to come along, so I can stop properly :thumbsup:

Picked up a Z33 midpipe today from Northshore Prestige (thanks Guys). Thats an upgrade to the massive/quiet centre muff that on there. Apparently just got to get it extended 6 inches...

Awesome to see some upgrades for the PM Alex!

Anyone know what the Tein Super Wagon's are like? Harsh as f**k?

There's a bit of anti Tein sentiments here ain't there? :teehee:

No, not at all.

From all accounts they are a very, very good kit but when there are other excellent kits floating around and cost considerably less, well I guess that's why most of us don't have them.

I still would like to buy a set of Teins. The price was crazy last time I looked though.>_<

Also:

Are you guys talking about crap brakes on the stag because you:

1. Have crap pads?

2. Do heaps of braking/accel during 'spirited' driving, and the brakes can't dissipate the heat soak so you get fade (could be fluid related though)?

3. Just want bling?

I would really like to know!

I've done a few bedding in stops to bed the pads properly into my machined rotors (stupid compliance workshop....), and it pulls up a treat now. ABS works too! :thumbsup:

I've also changed the fluid from DOT3 over to my ELF semi-racing fluid that I use in the Datto.

I still would like to buy a set of Teins. The price was crazy last time I looked though.>_<

Also:

Are you guys talking about crap brakes on the stag because you:

1. Have crap pads?

2. Do heaps of braking/accel during 'spirited' driving, and the brakes can't dissipate the heat soak so you get fade (could be fluid related though)?

3. Just want bling?

I would really like to know!

I've done a few bedding in stops to bed the pads properly into my machined rotors (stupid compliance workshop....), and it pulls up a treat now. ABS works too! :thumbsup:

I've also changed the fluid from DOT3 over to my ELF semi-racing fluid that I use in the Datto.

Im going to go the route of new rotors & pads shortly, but stock calipers. Will see how it goes, I wont be 'tracking' my car so I dont think I reallllly need big f'off brakes.

Would be interesting to see a comparison between R33 / Brembo / Stock in pull up distances from 60km/h. Doubt it'll happen though.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
    • For race cars, this is one part where I find having the roll cage bar having gone through a hole in the floor better than the build it up on a ledge inside... The Merc I help on, the main hoop ends are marked on the car, and the jack is marked... Jack goes under a few inches and lifts one whole side of the car up... Removes that fight for long slim jacks for race car duties!   My biggest issue for the daily drivers I work on, is my jacks don't go high enough. The jacks start out on a few blocks, jack it up, then start a second jack under it on more blocks, and then I can get an axle stand under it. My axle stands are presently in use, and are nearly fully extended. The car is sitting with barely more than a cm of clearance to get the wheel off the studs! Sarah's Kluger is the same, as it has an ungodly amount of droop available in the suspension and a distinct lack of good jacking points!
    • Happy? Yep, my to do list is getting shorter and shorter. Either this light approaching is the end of the tunnel, or I'm about to be hit by a train... Ha ha ha   Also, Duncan isn't that far out of town that you need to make a multi day drive out of it. 😛
    • Sorry I meant that we are building the EH for a client.
    • LOL, when one "money pit" is never enough Noice, and excellent work mate
×
×
  • Create New...