Jump to content
SAU Community

Recommended Posts

I've got pretty much the same ones as Josh.

Second what he has to say on Ecutalk too......

Only thing im over is when I plug in and clear codes it always throws an auto trans code.... Funny that as its manual these days!

i think our o2 actually fiddle with timing itself. everytime Cihan tried tuning mine previously with the o2 plugged in, the tune would just go out of whack on the next run.

i unplugged it, and it was fine from there on - that being said my o2 was f**ked. but i dont think its necessary if your tuning.

You can tune light load around stoichiometric or a whisker leaner and run without the factory O2 sensor without issue. Although there is a case for leaving some light/medium sections of the map a little richer so that you get a little more response in open loop but will be leaned back by the O2 sensor if you have constant throttle in that section of the map.

Tune going out of whack is a little odd. If he has written the values and they have been saved correctly then there should be no issues. If the O2 sensor is playing up then the ecu will be having issues jumping between closed and open loop. If the O2 sensor is throwing strange voltages then the closed loop mapping will be all over the place. Something that should be pretty easy to diagnose.

there is no vehicle specific software, consult is just the protocol that all nissans between about 1989 - 2002 use. and there is plenty of free software floating around. i've got a few, ECUTalk, Conzult Free, TECU, Nissan Scantech (i think this ones free). If you want to shell out some money you could use Nissan Datascan. even the Nistune software will perform consult operations.

If your looking for a good solid little program to check error codes, look at gauge readouts and some data logging than look at ECUTalk. its a great little program, i used to use it all the time before i got my nistune software licence. As far as i know there aren't any free consult programs that can run active tests, i think the free conzult can but its limited.

I prefer Datascan over ECUTalk. I have NIStune on the carpc as well but it's too full on for day-to-day monitoring/diagnostics. Not sure about windows7 though.. carpc is still running XP :blush:

I decided to throw my car on the Dyno today, just to see everything is running safe.

Dyno.JPG

Put out 215KW and was told that I should add 15KW on top of that due to the Dyno running low...

Looking forward to tuning it now... :thumbsup:

Great stuff Chris :thumbsup:

What are your current mods?

Cheers.

Sierra Stage 1 Highflow

Full Exhaust

HDI Intercooler

Runner Spacer

Air Filter

Standard ECU

I have bigger injectors / Emanage / EBC / suction pipe still to go in. Then the gearbox will probably need a little love... :ermm:

I decided to throw my car on the Dyno today, just to see everything is running safe.

Put out 215KW and was told that I should add 15KW on top of that due to the Dyno running low...

Looking forward to tuning it now... :thumbsup:

Nice! been on that Dyno....

I got nowhere near that!:ermm:

Cheers.

Sierra Stage 1 Highflow

Full Exhaust

HDI Intercooler

Runner Spacer

Air Filter

Standard ECU

I have bigger injectors / Emanage / EBC / suction pipe still to go in. Then the gearbox will probably need a little love... :ermm:

Agree with cam! That is really good with the stock ecu

post-77654-0-94582100-1301644434_thumb.jpgpost-77654-0-87307600-1301644427_thumb.jpgThought I'de take some pictures seeing as I washed the POS.

excuse the failed attempt at photography on the iphone lol

2 pics of the exhaust

post-77654-0-25349800-1301644406_thumb.jpg

post-77654-0-98127000-1301644420_thumb.jpg

and my failed attempts

post-77654-0-26105400-1301644414_thumb.jpg

post-77654-0-94582100-1301644434_thumb.jpg

post-77654-0-87307600-1301644427_thumb.jpg

post-77654-0-93916400-1301644657_thumb.jpg

im pretty happy with how its looking.. even with the moustache

Cheers.

Sierra Stage 1 Highflow

Full Exhaust

HDI Intercooler

Runner Spacer

Air Filter

Standard ECU

I have bigger injectors / Emanage / EBC / suction pipe still to go in. Then the gearbox will probably need a little love... :ermm:

Interesting, particularly given you havent got a suction pipe but its often been said 200 was the upper limit with the stock one; irrespective - great result! The gear box seems to not like a whole heap much more power than what youre already putting down though >_<

On a side note, but not completely unrelated, my group buy injectors & fuel pump showed up today (Madaz dropped them off) :worship:

iUJtB.jpg

Nice Duncan, same squirters as im running.

Did they give you the dead time report with it? I have mine here if you need the lag time, I assume 1ms at 45psi @ 14v (should be close). You will need two of those pumps to flow anywhere near enough though. lol.

Chris, where's the graph mate? Post it up.

Nice Duncan, same squirters as im running.

Did they give you the dead time report with it? I have mine here if you need the lag time, I assume 1ms at 45psi @ 14v (should be close). You will need two of those pumps to flow anywhere near enough though. lol..

Dead time report? :whistling:Not that Im aware of, Im sure the guys at Willall will be able to work it out when the time comes, but any additional info that will make everything go smoothly is always appreciated :thumbsup: I dont plan on trying to max out these injectors any time soon - at least thered be no point with the GB, so the walbro should suffice.. for now.. :)

Finally got up to see my mate and get the NIStune board installed in my ECU, took all of about 20 mins :banana:

Made a few minor changes to make living with the Haltech a bit easier until I find time to remove it and repair the butchered loom :/

Set up the Z32 afm, have been running it since the stocker died but because the Haltech runs a map sensor it wasn't too much of an issue.. I thought.. turns out it was screwing with the TP so VCT was needing a lot more load to flick on, feels SO much better punting around the streets with it working properly! Also set the VCT enable temp to 50deg (as stock ECU is reading the temp ~20-25deg low) until I pull the Haltech out, then I'll chuck a stock water temp sender back in.

I can't believe what was supposed to be a respected workshop set it all up like this :no::domokun:

Edited by bubba

got my new digital HD tv tuner in today.

works awesome! had a few problems with placement. but ill hide it somewhere lol

big thanks to commsman (leon) for supplying it with instructions!

Managed to get my seats, coilovers, headunit and wheels on yesterday. Still sorting out height and fitment though.

img46271.jpg

Tough! Love how a set of rims can change the whole look of a car :thumbsup:. Side on shot?

Cheers.

Sierra Stage 1 Highflow

Full Exhaust

HDI Intercooler

Runner Spacer

Air Filter

Standard ECU

I have bigger injectors / Emanage / EBC / suction pipe still to go in. Then the gearbox will probably need a little love... :ermm:

Wow, 230awkw on stock injectors/ecu/intake pipe?

Interesting...:whistling:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yes. You will need to get the original boost sensor and wire it in. That is.... if you plan to use a stock ECU - even a Nistuned ECU. The Nissan ECU will not operate correctly without it connected. And yes, it will do annoying stuff like you are experiencing. You will almost certainly be better off with some aftermarket ECU, than trying to hunt down rare sensors.
    • Ok so ABS/TCS is "not" the problem. Yeah i know now about the ABS with Nistune(i told that to the Nistune guy) but iam not 100% why or why i dont have ABS. ABS cube is in the engine (always has been) but i had braked couple of times rly hard and brakes just locked and scream. Does all Skylines have ABS cube? That boost sensor https://www.sau.com.au/forums/topic/367633-wtb-r34-gtt-turbo-pressure-sensor-pics-inside/ Is this it? I need to ask but i have a picture of engine bay and i do not see that (100% is not in that place) If i do not have this the car can do what mine is?(cutting around 4000 rpm) Here is the pic of my engine bay(only one i have) BUT i think i dont have that cuz loom was used from my RB20DE NEO and i know (obviously) that it does not have boost control or any wire to that...) so maybe that is the problem? (i dont know for 100% if that car where the engine is from had that)...but i dont have the loom from that
    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
×
×
  • Create New...