Jump to content
SAU Community

Recommended Posts

I'm rebuilding a VQ25det at the moment, it seems Nissan cant sell me any big end rod bearings... Wat?

I wonder if VQ35 ones will fit, anyone know a way to find out? I guess I will have to measure the stock rods and compare them somehow...

I didn't do anything....

But Scotty saved me by sourcing and fitting a new rad this afternoon, after mine decided it no longer wanted to keep the water on the inside... Bleeding the cooling system is a biatch...

Good to finally meet Aaron as well after all these years..

Thanks again mate!!! :cheers:

the bearing grades will be very minor differences in clearance...probably 1/10th of 20thou. If you are not buying nissan they will only have one grade. If you are buying nissan you could carefully measure everything....or just pick the middle grade and go with that

I didn't do anything....

But Scotty saved me by sourcing and fitting a new rad this afternoon, after mine decided it no longer wanted to keep the water on the inside... Bleeding the cooling system is a biatch...

Good to finally meet Aaron as well after all these years..

Thanks again mate!!! :cheers:

How did it go on the way home Nick? I should have sold you that spare coolant mod, it would have been quicker to fit that than bleed your engine...

How did it go on the way home Nick? I should have sold you that spare coolant mod, it would have been quicker to fit that than bleed your engine...

Ran like a dream thanks Scott. Temp gauge sat where it is supposed to the whole way home. Also drove across all possible bumps to give it all a good shake for bubble movements..

Swapped out the battery, and as expected the little window was showing bright red... New battery has restored normal starting..

I didn't do anything....

But Scotty saved me by sourcing and fitting a new rad this afternoon, after mine decided it no longer wanted to keep the water on the inside... Bleeding the cooling system is a biatch...

Good to finally meet Aaron as well after all these years..

Thanks again mate!!! :cheers:

Ha good to finally meet you too mate! Glad Scott got it all sorted!

Just fitted the HKS sensors for the F-con. Nissan was nice enough to leave me a decent spot to drill and tap the IAT sensor into the pipe the BOV mounts to, and two holes blanked off that I can mount the MAP sensor to. Just need to plumb the MAP sensor in now, thinking directly to the plenum rather than try and tap another thing in where the factory sensors are.

Also dropped the oil, replaced with fresh 300V and a Greddy filter. Guess I've got one more fill with 300V, 1L left over :/

Best measure of intake pressure is in the end of the plenum. Same place Nissan put the barb for the OEM sensor.

Right I'm with you now, the tiny hose on the end. Although there's also a factory sensor in the BOV pipe too.

Went on a little cruise with the v35/36 club of WA.. theyve adopted m35's into the club as theres not many in the scene. Met my first m35 other than mine today as NickM91 came along for the cruise .. had a great time and shared lots of info.. :cheers:

post-97600-0-47701000-1354973242_thumb.jpg

post-97600-0-47576700-1354973255_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...