Jump to content
SAU Community

Recommended Posts

i can currently get toluene cheaper than 98 0ctane petrol .

what are peoples thoughts on using it in cars ?

can anyone one tell me what happens if you put too much in a standard car ?

or any other knowledge .

cheers

how the hell do you get it cheaper than 98? i spent ages trying to find it cheap over here and gave up

general consensus is you shouldnt run any more than 30% in a road car, which should be more than enough to make some decent fuel when mixxed with 98

Edited by JonnoHR31

Toluene used to be very popular for making racing fuels with mixes of between 10 -30% which gave an increase in RON of about 3. It is lead free and doesn't stuff O2 sensors. It will def make your car go faster if properly tuned. I don't know if there are any longterm downsides. As to toxicity - petrol and petrol fumes already contain aromatics and are bad for your health so in all cases avoid the fumes and getting it on your skin.

I looked into it for ages. Couldnt get it just off the street. I even asked a good mate who is a professional painter to get the stuff..... no go in the volume i wanted. Cut a long sotry short.... Upgrade your fuel system to handle E85. Once that is done its cheap and getting more and more easy to get.

E85 is not available at the pumps in NZ and very expensive to get. Note OP has a supply of toluene available at a good price. Petrol is not very good for you either - no-one is planning to drink the stuff.

Surely there are some old racers out there ( and we are talking 5 -10 years ago) who can advise of any downside to Toluene as a fuel?

E85 is not available at the pumps in NZ and very expensive to get. Note OP has a supply of toluene available at a good price. Petrol is not very good for you either - no-one is planning to drink the stuff.

Surely there are some old racers out there ( and we are talking 5 -10 years ago) who can advise of any downside to Toluene as a fuel?

I used to add a 20% mix of toluene to 98. The difference was quite noticable on the dyno over straight 98. Also added some measure of insurance when drag racing. This was back in 2004-2006.

Just wear gloves when you pour it and DON"T BREATH IT IN!!! A 30% mix is about all you can get away with.

Toluene is a little harder on your fuel lines, but who cares if you replace them every 3 or 4 years!

Cheers

Justin

http://en.wikipedia.org/wiki/Toluene Look at the list of things it will dissolve, and ask yourself what are all your fuel hoses made out of.

petrol also eats rubber, which is why you use fuel hose instead of standard rubber hoses in your fuel system.

cheers for that justin .

on a side note i do know someone that put a couple of tanks of it straight through a nx coupe . it did go alot better up top . said nx coupe was in no way maintained or tuned properly . and it still went long enough for it to be crashed into a wall .

what happens if you run 100% in an untuned car ? will it lean out and melt some ringlands ?

  • 4 weeks later...

I've ran toluene in my cars, lawn mowers, weed trimmers, etc. for years and hadn't had any problems.  Now experimenting with moth balls (real naphthalene) and carb/throttle body cleaners (ingredients appear similar to bottled octane boosters, and dissolves moth balls quickly).  I wish there was an easy and reliable way to test octane for the average person. My neighbors probably think that I am running a meth lab at home.

Direct from wiki:

"Toluene at 86% by volume fueled all the turbo Formula 1 teams in the 1980s, first pioneered by the Honda team. The remaining 14% was a "filler" of n-heptane, to reduce the octane to meet Formula 1 fuel restrictions. Toluene at 100% can be used as a fuel for both two-stroke and four-stroke engines; however, due to the density of the fuel and other factors, the fuel does not vaporize easily unless preheated to 70 degrees Celsius (Honda accomplished this in their Formula 1 cars by routing the fuel lines through the muffler system to heat the fuel). Toluene also poses similar problems as alcohol fuels, as it eats through standard rubber fuel lines and has no lubricating properties as standard gasoline does, which can break down fuel pumps and cause upper cylinder bore wear."

In other words, it does not suit Joe Blow back yarders trying to save a buck. Engine(s) cost more than fuel in the long run.

Google time.

good luck, i spent a fair bit of time looking into it a while back and couldnt find any for less than ~$10/L here in perth, which is too expensive to use as a fuel. cheaper to buy e85 drums

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I get that taking off the head is best but that's a bit much for "just" valve seals. I was just under the impression that one would be able to rotate to TDC and be able to temporarily drop the valve without losing it and effectively having to remove the head to then recover it. I never knew people actually pushed rope into the cylinder to do valve seals hahaha So just to confirm, just going to TDC will not work? In that case I know when I do valve seals I'll maybe just remove the head and do some other things while I'm there, or just wait until I do an engine build.
    • The old approach was to fill the cylinder/chamber with a length of rope pushed in through the sparkplug hole. The new approach is to connect compressed air to the sparkplug hole and fill it with enough pressure to push the valves up. Doing either of these things with the head on and the engine in the car is a lot less pleasant than doing it properly.
    • Can't you put the pistons to TDC and then do the valve seals? Or will the drop down too far to pull them back up?
    • One thing I can tell you is, do it properly the first time. If you encounter unexpected problems just let the car sit for a week or two if you have to get some other parts or figure stuff out.  I'd have said go and use as many OEM parts as possible but since you want to change the turbo later on a custom kit is probably the better choice. Since I have no experience with RB25 just compare parts diagrams and images before buying a line kit and it should be easy to see if it has everything you need. Amayama has very good parts diagrams and part number lists, that is what I used a bunch to figure out what I might need. And don't forget to plan ahead and possibly renew other stuff that's easy to get to while you're in there doing the turbo lines. Happy wrenching
    • Update 4:   Hi all, good news. Engine is running and all the gaskets and seals seem to be working as intended. No leaks so far, even the JB Weld seems to hold. I flushed out the old coolant a few times and put in fresh coolant, not Nissan stuff, I decided to try the Ravenol Protect FL22, they claim it works for a wide variety of JDM cars and the opinions on it by some people were pretty good. And it has the nice poison green color! And man am I glad I bought a coolant system tester earlier this year, vacuum filling works wonders on this engine. I can definitely recommend this to anyone still doing it the old school way. All you need is compressed air supply. Will have to do a small test drive as soon as I can, I removed the gauge cluster again as the tacho needle was still bouncing around a bit but it was much better than before already.  I also found some cracks on all 4 tires inner and outer sidewalls. Apparently these tires should 't be parked on for extended periods or be kept under 0 degrees during storage, which I did not know. Clearly the previous owner didn't look into those details either, he probably bought them just cause they are cool semi-slicks. I'm just wondering how tf I am supposed to reach 30-80 degree tire temperatures on the public road consistenly, these tires were never going to work for my use case. I'll probably order Continental SportContact7 ones as these are the best allround summer tire available right now and I don't think I'll need anything crazier for now. Do let me know if you have experience with various tires and which ones you recommend.
×
×
  • Create New...